Corresponding Radial Force Required at Each Ball for Spring Loaded Governors Solution

STEP 0: Pre-Calculation Summary
Formula Used
Corresponding Radial Force Required at Each Ball = (Force Required at Sleeve to Overcome Friction*Length of sleeve arm of lever)/(2*Length of ball arm of lever)
FB = (FS*y)/(2*xball arm)
This formula uses 4 Variables
Variables Used
Corresponding Radial Force Required at Each Ball - (Measured in Newton) - The Corresponding Radial Force Required at Each Ball is any interaction that, when unopposed, will change the motion of an object.
Force Required at Sleeve to Overcome Friction - (Measured in Newton) - Force Required at Sleeve to Overcome Friction is any interaction that, when unopposed, will change the motion of an object.
Length of sleeve arm of lever - (Measured in Meter) - Length of sleeve arm of lever is a measure of how long the sleeve arm is.
Length of ball arm of lever - (Measured in Meter) - Length of ball arm of lever is a measure of how long the ball arm is.
STEP 1: Convert Input(s) to Base Unit
Force Required at Sleeve to Overcome Friction: 9 Newton --> 9 Newton No Conversion Required
Length of sleeve arm of lever: 1.2 Meter --> 1.2 Meter No Conversion Required
Length of ball arm of lever: 0.6 Meter --> 0.6 Meter No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
FB = (FS*y)/(2*xball arm) --> (9*1.2)/(2*0.6)
Evaluating ... ...
FB = 9
STEP 3: Convert Result to Output's Unit
9 Newton --> No Conversion Required
FINAL ANSWER
9 Newton <-- Corresponding Radial Force Required at Each Ball
(Calculation completed in 00.004 seconds)

Credits

Created by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has created this Calculator and 2000+ more calculators!
Verified by Payal Priya
Birsa Institute of Technology (BIT), Sindri
Payal Priya has verified this Calculator and 1900+ more calculators!

13 Basics of Governor Calculators

Total Downward Force on Sleeve in Wilson-Hartnell Governor
Go Force = Mass on Sleeve*Acceleration due to Gravity+(Tension in the auxiliary spring*Distance of auxiliary spring from mid of lever)/Distance of main spring from mid point of lever
Speed of Rotation in RPM
Go Mean Equilibrium Speed in RPM = 60/(2*pi)*sqrt((tan(Angle b/w axis of radius of rotation & line OA))/Mass of Ball)
Ratio of Length of Arm to Length of Link
Go Ratio of Length of Link to Length of Arm = tan(Angle of Inclination of Link to Vertical)/tan(Angle of Inclination of Arm to Vertical)
Corresponding Radial Force Required at Each Ball for Spring Loaded Governors
Go Corresponding Radial Force Required at Each Ball = (Force Required at Sleeve to Overcome Friction*Length of sleeve arm of lever)/(2*Length of ball arm of lever)
Angle between Axis of Radius of Rotation and Line Joining Point on Curve to Origin O
Go Angle b/w axis of radius of rotation & line OA = atan(Controlling Force/Radius of Rotation if Governor is in Mid-Position)
Angle between Axis of Radius of Rotation and Line Joining Point on Curve to Origin
Go Angle b/w axis of radius of rotation & line OA = atan(Mass of Ball*Mean Equilibrium Angular Speed^2)
Mean Equilibrium Speed in RPM
Go Mean Equilibrium Speed in RPM = (Minimum equilibrium speed in r.p.m+Maximum equilibrium speed in r.p.m)/2
Mean Equilibrium Angular Speed
Go Mean Equilibrium Angular Speed = (Minimum equilibrium angular speed+Maximum equilibrium angular speed)/2
Sleeve Load for Decrease in Speed Value when Taking Friction into Account
Go Sleeve load for decrease in speed = Total load on sleeve-Force Required at Sleeve to Overcome Friction
Sleeve Load for Increase in Speed Value when Taking Friction into Account
Go Sleeve load for increase in speed = Total load on sleeve+Force Required at Sleeve to Overcome Friction
Increased Speed
Go Increased Speed = Mean Equilibrium Speed in RPM*(1+Percentage Increase in Speed)
Governor Power
Go Power = Mean Effort*Lift of Sleeve
Height of Watt Governor
Go Height of Governor = 895/(Speed in RPM^2)

Corresponding Radial Force Required at Each Ball for Spring Loaded Governors Formula

Corresponding Radial Force Required at Each Ball = (Force Required at Sleeve to Overcome Friction*Length of sleeve arm of lever)/(2*Length of ball arm of lever)
FB = (FS*y)/(2*xball arm)

What is governor?

A governor is a system that is used to maintain the mean speed of an engine, within certain limits, under fluctuating load conditions. It does this by regulating and controlling the amount of fuel supplied to the engine.

How to Calculate Corresponding Radial Force Required at Each Ball for Spring Loaded Governors?

Corresponding Radial Force Required at Each Ball for Spring Loaded Governors calculator uses Corresponding Radial Force Required at Each Ball = (Force Required at Sleeve to Overcome Friction*Length of sleeve arm of lever)/(2*Length of ball arm of lever) to calculate the Corresponding Radial Force Required at Each Ball, The Corresponding radial force required at each ball for spring loaded governors formula is defined as any interaction that, when unopposed, will change the motion of an object. Corresponding Radial Force Required at Each Ball is denoted by FB symbol.

How to calculate Corresponding Radial Force Required at Each Ball for Spring Loaded Governors using this online calculator? To use this online calculator for Corresponding Radial Force Required at Each Ball for Spring Loaded Governors, enter Force Required at Sleeve to Overcome Friction (FS), Length of sleeve arm of lever (y) & Length of ball arm of lever (xball arm) and hit the calculate button. Here is how the Corresponding Radial Force Required at Each Ball for Spring Loaded Governors calculation can be explained with given input values -> 9 = (9*1.2)/(2*0.6).

FAQ

What is Corresponding Radial Force Required at Each Ball for Spring Loaded Governors?
The Corresponding radial force required at each ball for spring loaded governors formula is defined as any interaction that, when unopposed, will change the motion of an object and is represented as FB = (FS*y)/(2*xball arm) or Corresponding Radial Force Required at Each Ball = (Force Required at Sleeve to Overcome Friction*Length of sleeve arm of lever)/(2*Length of ball arm of lever). Force Required at Sleeve to Overcome Friction is any interaction that, when unopposed, will change the motion of an object, Length of sleeve arm of lever is a measure of how long the sleeve arm is & Length of ball arm of lever is a measure of how long the ball arm is.
How to calculate Corresponding Radial Force Required at Each Ball for Spring Loaded Governors?
The Corresponding radial force required at each ball for spring loaded governors formula is defined as any interaction that, when unopposed, will change the motion of an object is calculated using Corresponding Radial Force Required at Each Ball = (Force Required at Sleeve to Overcome Friction*Length of sleeve arm of lever)/(2*Length of ball arm of lever). To calculate Corresponding Radial Force Required at Each Ball for Spring Loaded Governors, you need Force Required at Sleeve to Overcome Friction (FS), Length of sleeve arm of lever (y) & Length of ball arm of lever (xball arm). With our tool, you need to enter the respective value for Force Required at Sleeve to Overcome Friction, Length of sleeve arm of lever & Length of ball arm of lever and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!