Empirical constant for taper Solution

STEP 0: Pre-Calculation Summary
Formula Used
Empirical Constant = (Larger Diameter-Smaller Diameter)/(2*Depth of Machined Surface*Smaller Diameter^2)
KT = (Dsd-d)/(2*Hsd*d^2)
This formula uses 4 Variables
Variables Used
Empirical Constant - Empirical constant is defined as the constant used to calculate the Taper produced during EDM due to side sparks.
Larger Diameter - (Measured in Meter) - Larger diameter is the bigger diameter of hole or other things.
Smaller Diameter - (Measured in Meter) - The smaller diameter is the smaller of all diameters of a given object.
Depth of Machined Surface - (Measured in Meter) - Depth of machined surface is the how deep a surface is machined from the un-machined surface.
STEP 1: Convert Input(s) to Base Unit
Larger Diameter: 22 Meter --> 22 Meter No Conversion Required
Smaller Diameter: 1.2 Meter --> 1.2 Meter No Conversion Required
Depth of Machined Surface: 52 Meter --> 52 Meter No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
KT = (Dsd-d)/(2*Hsd*d^2) --> (22-1.2)/(2*52*1.2^2)
Evaluating ... ...
KT = 0.138888888888889
STEP 3: Convert Result to Output's Unit
0.138888888888889 --> No Conversion Required
FINAL ANSWER
0.138888888888889 0.138889 <-- Empirical Constant
(Calculation completed in 00.020 seconds)

Credits

Created by Rajat Vishwakarma
University Institute of Technology RGPV (UIT - RGPV), Bhopal
Rajat Vishwakarma has created this Calculator and 400+ more calculators!
Verified by Vaibhav Malani
National Institute of Technology (NIT), Tiruchirapalli
Vaibhav Malani has verified this Calculator and 200+ more calculators!

9 Taper Formation Calculators

Volume of crater made by electric spark
Go Volume of Crater = (pi/12)*Depth of Machined Surface*((Smaller Diameter^2)+(Larger Diameter^2)+(Larger Diameter*Smaller Diameter))
Empirical constant for taper
Go Empirical Constant = (Larger Diameter-Smaller Diameter)/(2*Depth of Machined Surface*Smaller Diameter^2)
Depth of machined surface
Go Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Empirical Constant*Smaller Diameter^2)
Upper diameter of hole
Go Larger Diameter = 2*Depth of Machined Surface*Empirical Constant*Smaller Diameter^2+Smaller Diameter
Depth of machined surface given taper
Go Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Taper Produced in EDM)
Smaller diameter of crater given Taper
Go Smaller Diameter = Larger Diameter-2*Depth of Machined Surface*Taper Produced in EDM
Largest size of hole given taper
Go Larger Diameter = 2*Depth of Machined Surface*Taper Produced in EDM+Smaller Diameter
Smallest diameter of hole given empirical constant
Go Smaller Diameter = sqrt(Taper Produced in EDM/Empirical Constant)
Taper produced due to side sparks
Go Taper Produced in EDM = Empirical Constant*Smaller Diameter^2

Empirical constant for taper Formula

Empirical Constant = (Larger Diameter-Smaller Diameter)/(2*Depth of Machined Surface*Smaller Diameter^2)
KT = (Dsd-d)/(2*Hsd*d^2)

What factors affects surface finish during EDM?

The amount of material removed and the surface finish produced is dependent upon the current in the spark. The material removed by the spark can be assumed to be a crater. The amount removed therefore will depend upon the crater depth, which is directly proportional to the current. Thus as the material removed increases and at the same time the surface finish also decreases. However, decreasing the current in the spark, but increasing its frequency will improve the surface finish in view of the small crater size, but at the same time the material removal rate can be maintained by increasing the frequency.

How to Calculate Empirical constant for taper?

Empirical constant for taper calculator uses Empirical Constant = (Larger Diameter-Smaller Diameter)/(2*Depth of Machined Surface*Smaller Diameter^2) to calculate the Empirical Constant, The Empirical constant for taper formula is defined as the constant used to calculate the Taper produced during EDM due to side sparks. Empirical Constant is denoted by KT symbol.

How to calculate Empirical constant for taper using this online calculator? To use this online calculator for Empirical constant for taper, enter Larger Diameter (Dsd), Smaller Diameter (d) & Depth of Machined Surface (Hsd) and hit the calculate button. Here is how the Empirical constant for taper calculation can be explained with given input values -> 0.138889 = (22-1.2)/(2*52*1.2^2).

FAQ

What is Empirical constant for taper?
The Empirical constant for taper formula is defined as the constant used to calculate the Taper produced during EDM due to side sparks and is represented as KT = (Dsd-d)/(2*Hsd*d^2) or Empirical Constant = (Larger Diameter-Smaller Diameter)/(2*Depth of Machined Surface*Smaller Diameter^2). Larger diameter is the bigger diameter of hole or other things, The smaller diameter is the smaller of all diameters of a given object & Depth of machined surface is the how deep a surface is machined from the un-machined surface.
How to calculate Empirical constant for taper?
The Empirical constant for taper formula is defined as the constant used to calculate the Taper produced during EDM due to side sparks is calculated using Empirical Constant = (Larger Diameter-Smaller Diameter)/(2*Depth of Machined Surface*Smaller Diameter^2). To calculate Empirical constant for taper, you need Larger Diameter (Dsd), Smaller Diameter (d) & Depth of Machined Surface (Hsd). With our tool, you need to enter the respective value for Larger Diameter, Smaller Diameter & Depth of Machined Surface and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!