## Excess Temperature in Boiling Solution

STEP 0: Pre-Calculation Summary
Formula Used
Excess Temperature in Heat Transfer = Surface Temperature-Saturated Temperature
Te = TSurface-TSat
This formula uses 3 Variables
Variables Used
Excess Temperature in Heat Transfer - (Measured in Kelvin) - Excess Temperature in Heat Transfer is defined as the temperature difference between heat source and saturation temperature of the fluid.
Surface Temperature - (Measured in Kelvin) - Surface Temperature is the temperature at or near a surface. Specifically, it may refer to as Surface air temperature, the temperature of the air near the surface of the earth.
Saturated Temperature - (Measured in Kelvin) - Saturated temperature is the temperature at which a given liquid and its vapour or a given solid and its vapour can co-exist in equilibrium, at a given pressure.
STEP 1: Convert Input(s) to Base Unit
Surface Temperature: 402 Kelvin --> 402 Kelvin No Conversion Required
Saturated Temperature: 373 Kelvin --> 373 Kelvin No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
Te = TSurface-TSat --> 402-373
Evaluating ... ...
Te = 29
STEP 3: Convert Result to Output's Unit
29 Kelvin --> No Conversion Required
29 Kelvin <-- Excess Temperature in Heat Transfer
(Calculation completed in 00.015 seconds)
You are here -
Home »

## Credits

Created by Ayush gupta
University School of Chemical Technology-USCT (GGSIPU), New Delhi
Ayush gupta has created this Calculator and 200+ more calculators!
Verified by Soupayan banerjee
National University of Judicial Science (NUJS), Kolkata
Soupayan banerjee has verified this Calculator and 300+ more calculators!

## < 10+ Boiling and Condensation Formulas Calculators

Film Thickness in Film Condensation
Film Thickness = ((4*Viscosity of Film*Thermal Conductivity*Height of Film*(Saturated Temperature-Plate Surface Temperature))/([g]*Latent Heat of Vaporization*(Density of Liquid)*(Density of Liquid-Density of Vapor)))^(0.25) Go
Radius of Vapour Bubble in Mechanical Equilibrium in Superheated Liquid
Radius of Vapor Bubble = (2*Surface Tension*[R]*(Saturated Temperature^2))/(Pressure of Superheated Liquid*Enthalpy of Vaporization of Liquid*(Temperature of Superheated Liquid-Saturated Temperature)) Go
Reynolds Number using Average Heat Transfer Coefficient for Condensate Film
Reynolds Number of Film = ((4*Average Heat Transfer Coefficient*Length of Plate* (Saturated Temperature-Plate Surface Temperature))/ (Latent Heat of Vaporization*Viscosity of Film)) Go
Radiation Heat Transfer Coefficient = (([Stefan-BoltZ]*Emissivity*(((Plate Surface Temperature)^4)-((Saturated Temperature)^4)))/(Plate Surface Temperature-Saturated Temperature)) Go
Total Heat Transfer Coefficient
Total Heat Transfer Coefficient = Heat Transfer Coefficient in Film Boiling Region* ((Heat Transfer Coefficient in Film Boiling Region/Heat Transfer Coefficient)^(1/3))+Radiation Heat Transfer Coefficient Go
Mass Flow of Condensate through any X Position of Film
Mass Flow Rate = Density of Liquid*(Density of Liquid-Density of Vapor)*[g]*(Film Thickness^3)/(3*Viscosity of Film) Go
Modified Heat of Vaporization
Modified Heat of Vaporization = (Latent Heat of Vaporization+(Specific Heat of Water Vapour)*((Plate Surface Temperature-Saturated Temperature)/2)) Go
Energy Balance for Non-linear Temperature Profile in Film
New Latent Heat of Vaporization = (Latent Heat of Vaporization+0.68*Specific Heat Capacity*(Saturated Temperature-Plate Surface Temperature)) Go
Reynolds Number for Condensate Film
Reynolds Number of Film = (4*Mass Flow of Condensate)/(Wetted Perimeter*Viscosity of Fluid) Go
Excess Temperature in Boiling
Excess Temperature in Heat Transfer = Surface Temperature-Saturated Temperature Go

## Excess Temperature in Boiling Formula

Excess Temperature in Heat Transfer = Surface Temperature-Saturated Temperature
Te = TSurface-TSat

## What is Heat Transfer?

Heat transfer is a discipline of thermal engineering that concerns the generation, use, conversion, and exchange of thermal energy between physical systems. Heat transfer is classified into various mechanisms, such as thermal conduction, thermal convection, thermal radiation, and transfer of energy by phase changes.

## Define Thermal Conductivity & Factors affecting it?

Thermal conductivity is defined as the ability of a substance to conduct heat. Factors Affecting The Thermal Conductivity are: Moisture, Density of material, Pressure, Temperature & Structure of material.

## How to Calculate Excess Temperature in Boiling?

Excess Temperature in Boiling calculator uses Excess Temperature in Heat Transfer = Surface Temperature-Saturated Temperature to calculate the Excess Temperature in Heat Transfer, The Excess Temperature in Boiling formula is defined as the difference between the surface temperature and saturated temperature. Excess Temperature in Heat Transfer is denoted by Te symbol.

How to calculate Excess Temperature in Boiling using this online calculator? To use this online calculator for Excess Temperature in Boiling, enter Surface Temperature (TSurface) & Saturated Temperature (TSat) and hit the calculate button. Here is how the Excess Temperature in Boiling calculation can be explained with given input values -> 29 = 402-373.

### FAQ

What is Excess Temperature in Boiling?
The Excess Temperature in Boiling formula is defined as the difference between the surface temperature and saturated temperature and is represented as Te = TSurface-TSat or Excess Temperature in Heat Transfer = Surface Temperature-Saturated Temperature. Surface Temperature is the temperature at or near a surface. Specifically, it may refer to as Surface air temperature, the temperature of the air near the surface of the earth & Saturated temperature is the temperature at which a given liquid and its vapour or a given solid and its vapour can co-exist in equilibrium, at a given pressure.
How to calculate Excess Temperature in Boiling?
The Excess Temperature in Boiling formula is defined as the difference between the surface temperature and saturated temperature is calculated using Excess Temperature in Heat Transfer = Surface Temperature-Saturated Temperature. To calculate Excess Temperature in Boiling, you need Surface Temperature (TSurface) & Saturated Temperature (TSat). With our tool, you need to enter the respective value for Surface Temperature & Saturated Temperature and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well. Let Others Know