Hydrostatic Contact Force given Bolt Load under Operating condition Solution

STEP 0: Pre-Calculation Summary
Formula Used
Total Joint Surface Compression Load = Bolt Load Under Operating Condition for Gasket-((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket)
Hp = Wm1-((pi/4)*(G)^2*P)
This formula uses 1 Constants, 4 Variables
Constants Used
pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288
Variables Used
Total Joint Surface Compression Load - (Measured in Newton) - Total Joint Surface Compression Load is defined as the force offered by a joint on the contact surface or an object which is in contact with that force.
Bolt Load Under Operating Condition for Gasket - (Measured in Newton) - Bolt Load Under Operating Condition for Gasket is defined as the load acting on a bolt, it is limited to the amount of load the bolt can handle before failing.
Gasket Diameter - (Measured in Meter) - Gasket Diameter is a straight line passing from side to side through the centre of a gasket.
Pressure at Outer Diameter of Gasket - (Measured in Pascal) - Pressure at Outer Diameter of Gasket is the amount of force acting per unit area on the outer periphery of the gasket.
STEP 1: Convert Input(s) to Base Unit
Bolt Load Under Operating Condition for Gasket: 15486 Newton --> 15486 Newton No Conversion Required
Gasket Diameter: 32 Millimeter --> 0.032 Meter (Check conversion here)
Pressure at Outer Diameter of Gasket: 3.9 Megapascal --> 3900000 Pascal (Check conversion here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
Hp = Wm1-((pi/4)*(G)^2*P) --> 15486-((pi/4)*(0.032)^2*3900000)
Evaluating ... ...
Hp = 12349.433894656
STEP 3: Convert Result to Output's Unit
12349.433894656 Newton --> No Conversion Required
FINAL ANSWER
12349.433894656 12349.43 Newton <-- Total Joint Surface Compression Load
(Calculation completed in 00.020 seconds)

Credits

Created by sanjay shiva
national institute of technology hamirpur (NITH ), hamirpur , himachal pradesh
sanjay shiva has created this Calculator and 100+ more calculators!
Verified by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has verified this Calculator and 2500+ more calculators!

16 Bolt Loads in Gasket Joints Calculators

Bolt Load under operating condition given Hydrostatic End Force
Go Bolt Load Under Operating Condition for Gasket = ((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket)+(2*Width of u-collar*pi*Gasket Diameter*Pressure at Outer Diameter of Gasket*Gasket Factor)
Hydrostatic End Force given Bolt Load under Operating condition
Go Hydrostatic End Force in Gasket Seal = Bolt Load Under Operating Condition for Gasket-(2*Width of u-collar*pi*Gasket Diameter*Gasket Factor*Pressure at Outer Diameter of Gasket)
Hydrostatic Contact Force given Bolt Load under Operating condition
Go Total Joint Surface Compression Load = Bolt Load Under Operating Condition for Gasket-((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket)
Actual Cross-sectional Area of Bolts given Root Diameter of Thread
Go Actual Bolt Area = (2*pi*Gasket Unit Seating Load*Gasket Diameter*Gasket Width)/(Stress Required for Gasket Seating)
Gasket Width given actual Cross-sectional Area of Bolts
Go Gasket Width = (Stress Required for Gasket Seating*Actual Bolt Area)/(2*pi*Gasket Unit Seating Load*Gasket Diameter)
Stress Required for Gasket Seating
Go Stress Required for Gasket Seating = (2*pi*Gasket Unit Seating Load*Gasket Diameter*Gasket Width)/(Actual Bolt Area)
Stress Required for Gasket Seating given Bolt Load
Go Stress Required for Gasket Seating = Bolt Load Under Operating Condition for Gasket/((Greater Cross-section Area of Bolts+Actual Bolt Area)/2)
Bolt Load in Design of Flange for Gasket Seating
Go Bolt Load Under Operating Condition for Gasket = ((Greater Cross-section Area of Bolts+Actual Bolt Area)/2)*Stress Required for Gasket Seating
Width of U Collar given Initial Bolt Load to Seat Gasket Joint
Go Width of u-collar = Initial bolt load to seat the gasket joint/(pi*Gasket Diameter*Gasket Unit Seating Load)
Deflection of Spring Initial Bolt Load to Seal Gasket Joint
Go Gasket Unit Seating Load = Initial bolt load to seat the gasket joint/(pi*Width of u-collar*Gasket Diameter)
Initial Bolt Load to seat Gasket Joint
Go Initial bolt load to seat the gasket joint = pi*Width of u-collar*Gasket Diameter*Gasket Unit Seating Load
Test pressure given Bolt Load
Go Test Pressure in Bolted Gasket Joint = Bolt Load in Gasket Joint/(Factor of Safety for Bolt Packing*Greater Cross-section Area of Bolts)
Load on bolts based on hydrostatic end force
Go Bolt Load in Gasket Joint = Factor of Safety for Bolt Packing*Test Pressure in Bolted Gasket Joint*Greater Cross-section Area of Bolts
Total cross-sectional area of bolt at root of thread
Go Bolt Cross-sectional Area at Root of Thread = Bolt Load Under Operating Condition for Gasket/(Stress Required for Operating Condition for Gasket)
Bolt load under operating condition
Go Bolt Load Under Operating Condition for Gasket = Hydrostatic End Force in Gasket Seal+Total Joint Surface Compression Load
Hydrostatic end force
Go Hydrostatic End Force in Gasket Seal = Bolt Load Under Operating Condition for Gasket-Total Joint Surface Compression Load

Hydrostatic Contact Force given Bolt Load under Operating condition Formula

Total Joint Surface Compression Load = Bolt Load Under Operating Condition for Gasket-((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket)
Hp = Wm1-((pi/4)*(G)^2*P)

What is Hydrostatic contact force?

Hydrostatic contact force is defined as the normal force exerted by a liquid per unit area of the surface in contact

How to Calculate Hydrostatic Contact Force given Bolt Load under Operating condition?

Hydrostatic Contact Force given Bolt Load under Operating condition calculator uses Total Joint Surface Compression Load = Bolt Load Under Operating Condition for Gasket-((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket) to calculate the Total Joint Surface Compression Load, The Hydrostatic Contact Force given Bolt Load under Operating condition formula is defined as the normal force exerted by a liquid per unit area of the surface in contact. Total Joint Surface Compression Load is denoted by Hp symbol.

How to calculate Hydrostatic Contact Force given Bolt Load under Operating condition using this online calculator? To use this online calculator for Hydrostatic Contact Force given Bolt Load under Operating condition, enter Bolt Load Under Operating Condition for Gasket (Wm1), Gasket Diameter (G) & Pressure at Outer Diameter of Gasket (P) and hit the calculate button. Here is how the Hydrostatic Contact Force given Bolt Load under Operating condition calculation can be explained with given input values -> 12349.43 = 15486-((pi/4)*(0.032)^2*3900000).

FAQ

What is Hydrostatic Contact Force given Bolt Load under Operating condition?
The Hydrostatic Contact Force given Bolt Load under Operating condition formula is defined as the normal force exerted by a liquid per unit area of the surface in contact and is represented as Hp = Wm1-((pi/4)*(G)^2*P) or Total Joint Surface Compression Load = Bolt Load Under Operating Condition for Gasket-((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket). Bolt Load Under Operating Condition for Gasket is defined as the load acting on a bolt, it is limited to the amount of load the bolt can handle before failing, Gasket Diameter is a straight line passing from side to side through the centre of a gasket & Pressure at Outer Diameter of Gasket is the amount of force acting per unit area on the outer periphery of the gasket.
How to calculate Hydrostatic Contact Force given Bolt Load under Operating condition?
The Hydrostatic Contact Force given Bolt Load under Operating condition formula is defined as the normal force exerted by a liquid per unit area of the surface in contact is calculated using Total Joint Surface Compression Load = Bolt Load Under Operating Condition for Gasket-((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket). To calculate Hydrostatic Contact Force given Bolt Load under Operating condition, you need Bolt Load Under Operating Condition for Gasket (Wm1), Gasket Diameter (G) & Pressure at Outer Diameter of Gasket (P). With our tool, you need to enter the respective value for Bolt Load Under Operating Condition for Gasket, Gasket Diameter & Pressure at Outer Diameter of Gasket and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!