Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld Solution

STEP 0: Pre-Calculation Summary
Formula Used
Length of Parallel Fillet Weld = (Load on weld-0.707*Tensile Stress*Length of Single Fillet Lap Weld*Thickness of Plate)/(1.414*Shear Stress*Thickness of Plate)
Lparallel = (W-0.707*ฯƒt*Lsingle*tplate)/(1.414*๐œ*tplate)
This formula uses 6 Variables
Variables Used
Length of Parallel Fillet Weld - (Measured in Meter) - Length of Parallel Fillet Weld is the distance between two consecutive end of welds.
Load on weld - (Measured in Newton) - Load on weld is the instantaneous load applied perpendicular to the specimen cross section.
Tensile Stress - (Measured in Pascal) - Tensile Stress can be defined as the magnitude of force applied along the weld, which is divided by the cross-sectional area of the weld in a direction perpendicular to the applied force.
Length of Single Fillet Lap Weld - (Measured in Meter) - The Length of Single Fillet Lap Weld is the distance between two consecutive ends of welds.
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.
Shear Stress - (Measured in Pascal) - Shear Stress is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress.
STEP 1: Convert Input(s) to Base Unit
Load on weld: 9 Kilonewton --> 9000 Newton (Check conversion here)
Tensile Stress: 32 Megapascal --> 32000000 Pascal (Check conversion here)
Length of Single Fillet Lap Weld: 1.5 Millimeter --> 0.0015 Meter (Check conversion here)
Thickness of Plate: 12 Millimeter --> 0.012 Meter (Check conversion here)
Shear Stress: 2.4 Megapascal --> 2400000 Pascal (Check conversion here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
Lparallel = (W-0.707*ฯƒt*Lsingle*tplate)/(1.414*๐œ*tplate) --> (9000-0.707*32000000*0.0015*0.012)/(1.414*2400000*0.012)
Evaluating ... ...
Lparallel = 0.211004243281471
STEP 3: Convert Result to Output's Unit
0.211004243281471 Meter -->211.004243281471 Millimeter (Check conversion here)
FINAL ANSWER
211.004243281471 โ‰ˆ 211.0042 Millimeter <-- Length of Parallel Fillet Weld
(Calculation completed in 00.020 seconds)

Credits

Created by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has created this Calculator and 2000+ more calculators!
Verified by Payal Priya
Birsa Institute of Technology (BIT), Sindri
Payal Priya has verified this Calculator and 1900+ more calculators!

14 Analysis of Compound Weld Calculators

Length of Single Fillet Lap Weld given Total Load Carried by Plates in Compound Weld
Go Length of Single Fillet Lap Weld = (Load on weld-1.414*Shear Stress*Length of Parallel Fillet Weld*Thickness of Plate)/(0.707*Tensile Stress*Thickness of Plate)
Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld
Go Length of Parallel Fillet Weld = (Load on weld-0.707*Tensile Stress*Length of Single Fillet Lap Weld*Thickness of Plate)/(1.414*Shear Stress*Thickness of Plate)
Allowable Tensile Stress given Total Load Carried by Plates in Compound Weld
Go Tensile Stress = (Load on weld-1.414*Shear Stress*Length of Parallel Fillet Weld*Thickness of Plate)/(0.707*Length of Single Fillet Lap Weld*Thickness of Plate)
Maximum Shear Stress given Total Load Carried by Plates in Compound Weld
Go Shear Stress = (Load on weld-0.707*Tensile Stress*Length of Single Fillet Lap Weld*Thickness of Plate)/(1.414*Length of Parallel Fillet Weld*Thickness of Plate)
Total Load Carried by Plates in Compound Weld
Go Load on weld = 1.414*Shear Stress*Length of Parallel Fillet Weld*Thickness of Plate+0.707*Tensile Stress*Length of Single Fillet Lap Weld*Thickness of Plate
Thickness of Plates given Total Load Carried by Plates in Compound Weld
Go Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld+0.707*Tensile Stress*Length of Single Fillet Lap Weld)
Length of Single Fillet Lap Weld given Load Carried by Single Fillet Lap Weld
Go Length of Single Fillet Lap Weld = Load on weld/(0.707*Tensile Stress*Thickness of Plate)
Allowable Tensile Stress given Load Carried by Single Fillet Lap Weld
Go Tensile Stress = Load on weld/(0.707*Length of Single Fillet Lap Weld*Thickness of Plate)
Thickness of Plates given Load Carried by Single Fillet Lap Weld
Go Thickness of Plate = Load on weld/(0.707*Tensile Stress*Length of Single Fillet Lap Weld)
Load Carried by Single Fillet Lap Weld
Go Load on weld = 0.707*Tensile Stress*Length of Single Fillet Lap Weld*Thickness of Plate
Length of Parallel Fillet Weld given Load Carried by Parallel Fillet Weld
Go Length of Parallel Fillet Weld = Load on weld/(1.414*Shear Stress*Thickness of Plate)
Maximum Shear Stress given Load Carried by Parallel Fillet Weld
Go Shear Stress = Load on weld/(1.414*Length of Parallel Fillet Weld*Thickness of Plate)
Thickness of Plates given Load Carried by Parallel Fillet Weld
Go Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld)
Load Carried by Parallel Fillet Weld
Go Load on weld = 1.414*Shear Stress*Length of Parallel Fillet Weld*Thickness of Plate

Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld Formula

Length of Parallel Fillet Weld = (Load on weld-0.707*Tensile Stress*Length of Single Fillet Lap Weld*Thickness of Plate)/(1.414*Shear Stress*Thickness of Plate)
Lparallel = (W-0.707*ฯƒt*Lsingle*tplate)/(1.414*๐œ*tplate)

What do you mean by maximum shear stress theory?

The maximum shear stress theory states that the failure or yielding of a ductile material will occur when the maximum shear stress of the material equals or exceeds the shear stress value at the yield point in the uniaxial tensile test.

How to Calculate Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld?

Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld calculator uses Length of Parallel Fillet Weld = (Load on weld-0.707*Tensile Stress*Length of Single Fillet Lap Weld*Thickness of Plate)/(1.414*Shear Stress*Thickness of Plate) to calculate the Length of Parallel Fillet Weld, The Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld formula is defined as the distance between the two consecutive ends of the weld. Length of Parallel Fillet Weld is denoted by Lparallel symbol.

How to calculate Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld using this online calculator? To use this online calculator for Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld, enter Load on weld (W), Tensile Stress (ฯƒt), Length of Single Fillet Lap Weld (Lsingle), Thickness of Plate (tplate) & Shear Stress (๐œ) and hit the calculate button. Here is how the Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld calculation can be explained with given input values -> 211004.2 = (9000-0.707*32000000*0.0015*0.012)/(1.414*2400000*0.012).

FAQ

What is Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld?
The Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld formula is defined as the distance between the two consecutive ends of the weld and is represented as Lparallel = (W-0.707*ฯƒt*Lsingle*tplate)/(1.414*๐œ*tplate) or Length of Parallel Fillet Weld = (Load on weld-0.707*Tensile Stress*Length of Single Fillet Lap Weld*Thickness of Plate)/(1.414*Shear Stress*Thickness of Plate). Load on weld is the instantaneous load applied perpendicular to the specimen cross section, Tensile Stress can be defined as the magnitude of force applied along the weld, which is divided by the cross-sectional area of the weld in a direction perpendicular to the applied force, The Length of Single Fillet Lap Weld is the distance between two consecutive ends of welds, The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness & Shear Stress is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress.
How to calculate Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld?
The Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld formula is defined as the distance between the two consecutive ends of the weld is calculated using Length of Parallel Fillet Weld = (Load on weld-0.707*Tensile Stress*Length of Single Fillet Lap Weld*Thickness of Plate)/(1.414*Shear Stress*Thickness of Plate). To calculate Length of Parallel Fillet Weld given Total Load Carried by Plates in Compound Weld, you need Load on weld (W), Tensile Stress (ฯƒt), Length of Single Fillet Lap Weld (Lsingle), Thickness of Plate (tplate) & Shear Stress (๐œ). With our tool, you need to enter the respective value for Load on weld, Tensile Stress, Length of Single Fillet Lap Weld, Thickness of Plate & Shear Stress and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
How many ways are there to calculate Length of Parallel Fillet Weld?
In this formula, Length of Parallel Fillet Weld uses Load on weld, Tensile Stress, Length of Single Fillet Lap Weld, Thickness of Plate & Shear Stress. We can use 1 other way(s) to calculate the same, which is/are as follows -
  • Length of Parallel Fillet Weld = Load on weld/(1.414*Shear Stress*Thickness of Plate)
Let Others Know
โœ–
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!