Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force Solution

STEP 0: Pre-Calculation Summary
Formula Used
Mass Density of Steel = (Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))+Density of Drilling Mud)
ρs = (Te/([g]*As*(L-z))+ρm)
This formula uses 1 Constants, 6 Variables
Constants Used
[g] - Gravitational acceleration on Earth Value Taken As 9.80665
Variables Used
Mass Density of Steel - (Measured in Kilogram per Cubic Meter) - Mass Density of Steel varies based on the alloying constituents but usually ranges between 7,750 and 8,050 kg/m3.
Effective Tension - (Measured in Newton) - Effective Tension when buoyant force acts in a direction opposite to the gravity force.
Cross Section Area of Steel in Pipe - (Measured in Square Meter) - Cross Section Area of Steel in Pipe is the extent of a surface or plane figure as measured in square units.
Length of Pipe Hanging in Well - (Measured in Meter) - Length of Pipe Hanging in Well is essential in calculating all other values required in drilling.
Coordinate measured Downward from Top - Coordinate measured Downward from Top depends on tension on a Vertical Drill String.
Density of Drilling Mud - (Measured in Kilogram per Cubic Meter) - Density of Drilling Mud considering a steel drilling pipe hanging in an oil well.
STEP 1: Convert Input(s) to Base Unit
Effective Tension: 402.22 Kilonewton --> 402220 Newton (Check conversion here)
Cross Section Area of Steel in Pipe: 0.65 Square Meter --> 0.65 Square Meter No Conversion Required
Length of Pipe Hanging in Well: 16 Meter --> 16 Meter No Conversion Required
Coordinate measured Downward from Top: 6 --> No Conversion Required
Density of Drilling Mud: 1440 Kilogram per Cubic Meter --> 1440 Kilogram per Cubic Meter No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
ρs = (Te/([g]*As*(L-z))+ρm) --> (402220/([g]*0.65*(16-6))+1440)
Evaluating ... ...
ρs = 7750.00392590742
STEP 3: Convert Result to Output's Unit
7750.00392590742 Kilogram per Cubic Meter --> No Conversion Required
FINAL ANSWER
7750.00392590742 7750.004 Kilogram per Cubic Meter <-- Mass Density of Steel
(Calculation completed in 00.004 seconds)

Credits

Created by Mithila Muthamma PA
Coorg Institute of Technology (CIT), Coorg
Mithila Muthamma PA has created this Calculator and 2000+ more calculators!
Verified by M Naveen
National Institute of Technology (NIT), Warangal
M Naveen has verified this Calculator and 900+ more calculators!

18 Hydrostatics Calculators

Mass Density of Drilling Mud when Buoyant Force acts in Direction opposite to Gravity Force
Go Density of Drilling Mud = -((Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))-Mass Density of Steel))
Length of Pipe Hanging in Well given Effective Tension
Go Length of Pipe Hanging in Well = ((Effective Tension/((Mass Density of Steel-Density of Drilling Mud)*[g]*Cross Section Area of Steel in Pipe)+Coordinate measured Downward from Top))
Coordinate measured Downward from Top given Effective Tension
Go Coordinate measured Downward from Top = -(Effective Tension/((Mass Density of Steel-Density of Drilling Mud)*[g]*Cross Section Area of Steel in Pipe)-Length of Pipe Hanging in Well)
Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force
Go Mass Density of Steel = (Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))+Density of Drilling Mud)
Cross Section Area of Steel given Effective Tension
Go Cross Section Area of Steel in Pipe = Effective Tension/((Mass Density of Steel-Density of Drilling Mud)*[g]*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))
Effective Tension given Buoyant Force acts in Direction opposite to Gravity Force
Go Effective Tension = (Mass Density of Steel-Density of Drilling Mud)*[g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top)
Coordinate measured Downward from Top given Tension on Vertical Drill String
Go Coordinate measured Downward from Top = -((Tension on Vertical Drill String/(Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe))-Length of Pipe Hanging in Well)
Cross Section Area of Steel in Pipe given Tension on Vertical Drill String
Go Cross Section Area of Steel in Pipe = Tension on Vertical Drill String/(Mass Density of Steel*[g]*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))
Length of Pipe Hanging in Well given Tension on Vertical Drill String
Go Length of Pipe Hanging in Well = (Tension on Vertical Drill String/(Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe))+Coordinate measured Downward from Top
Mass Density of Steel for Tension on Vertical Drill String
Go Mass Density of Steel = Tension on Vertical Drill String/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))
Tension on Vertical Drill String
Go Tension on Vertical Drill String = Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top)
Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String
Go Length of Pipe Hanging in Well = Vertical Force at Bottom end of Drill String/(Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe)
Mass Density of Drilling Mud given Vertical Force at Bottom End of Drill String
Go Density of Drilling Mud = Vertical Force at Bottom end of Drill String/([g]*Cross Section Area of Steel in Pipe*Length of Pipe Hanging in Well)
Vertical Force at Bottom End of Drill String
Go Vertical Force at Bottom end of Drill String = Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe*Length of Pipe Hanging in Well
Mass Density of Drilling Mud for Lower Section of Drill String Length in Compression
Go Density of Drilling Mud = (Lower Section of Drill String Length*Mass Density of Steel)/Length of Pipe Hanging in Well
Length of Pipe Hanging given Lower Section of Drill String Length in Compression
Go Length of Pipe Hanging in Well = (Lower Section of Drill String Length*Mass Density of Steel)/Density of Drilling Mud
Mass Density of Steel for Lower Section of Drill String Length in Compression
Go Mass Density of Steel = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Lower Section of Drill String Length
Lower Section of Drill String Length that is in Compression
Go Lower Section of Drill String Length = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Mass Density of Steel

Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force Formula

Mass Density of Steel = (Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))+Density of Drilling Mud)
ρs = (Te/([g]*As*(L-z))+ρm)

What is Buoyancy?

Buoyancy is the force that causes objects to float. It is the force exerted on an object that is partly or wholly immersed in a fluid. Buoyancy is caused by the differences in pressure acting on opposite sides of an object immersed in a static fluid. It is also known as the buoyant force

How to Calculate Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force?

Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force calculator uses Mass Density of Steel = (Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))+Density of Drilling Mud) to calculate the Mass Density of Steel, The Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force for buoyant force considering ever-increasing string slice length. Mass Density of Steel is denoted by ρs symbol.

How to calculate Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force using this online calculator? To use this online calculator for Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force, enter Effective Tension (Te), Cross Section Area of Steel in Pipe (As), Length of Pipe Hanging in Well (L), Coordinate measured Downward from Top (z) & Density of Drilling Mud m) and hit the calculate button. Here is how the Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force calculation can be explained with given input values -> 7750.004 = (402220/([g]*0.65*(16-6))+1440).

FAQ

What is Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force?
The Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force for buoyant force considering ever-increasing string slice length and is represented as ρs = (Te/([g]*As*(L-z))+ρm) or Mass Density of Steel = (Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))+Density of Drilling Mud). Effective Tension when buoyant force acts in a direction opposite to the gravity force, Cross Section Area of Steel in Pipe is the extent of a surface or plane figure as measured in square units, Length of Pipe Hanging in Well is essential in calculating all other values required in drilling, Coordinate measured Downward from Top depends on tension on a Vertical Drill String & Density of Drilling Mud considering a steel drilling pipe hanging in an oil well.
How to calculate Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force?
The Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force for buoyant force considering ever-increasing string slice length is calculated using Mass Density of Steel = (Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))+Density of Drilling Mud). To calculate Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force, you need Effective Tension (Te), Cross Section Area of Steel in Pipe (As), Length of Pipe Hanging in Well (L), Coordinate measured Downward from Top (z) & Density of Drilling Mud m). With our tool, you need to enter the respective value for Effective Tension, Cross Section Area of Steel in Pipe, Length of Pipe Hanging in Well, Coordinate measured Downward from Top & Density of Drilling Mud and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
How many ways are there to calculate Mass Density of Steel?
In this formula, Mass Density of Steel uses Effective Tension, Cross Section Area of Steel in Pipe, Length of Pipe Hanging in Well, Coordinate measured Downward from Top & Density of Drilling Mud. We can use 2 other way(s) to calculate the same, which is/are as follows -
  • Mass Density of Steel = Tension on Vertical Drill String/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))
  • Mass Density of Steel = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Lower Section of Drill String Length
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!