Pressure Acting on Rolls from Entry Side Solution

STEP 0: Pre-Calculation Summary
Formula Used
Pressure Acting at Entry = Mean Yield Shear Stress at Entry*Thickness at Entry/Initial Thickness*exp(Coefficient of Friction*(2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle made by Point Roll Center and Normal*sqrt(The Roller Radius/Final Thickness after Rolling))-2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle of Bite*sqrt(The Roller Radius/Final Thickness after Rolling))))
Pe = Se*he/hin*exp(μrp*(2*sqrt(Rroller/hf)*atan(Θr*sqrt(Rroller/hf))-2*sqrt(Rroller/hf)*atan(αbite*sqrt(Rroller/hf))))
This formula uses 4 Functions, 9 Variables
Functions Used
tan - The tangent of an angle is a trigonometric ratio of the length of the side opposite an angle to the length of the side adjacent to an angle in a right triangle., tan(Angle)
atan - Inverse tan is used to calculate the angle by applying the tangent ratio of the angle, which is the opposite side divided by the adjacent side of the right triangle., atan(Number)
exp - n an exponential function, the value of the function changes by a constant factor for every unit change in the independent variable., exp(Number)
sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)
Variables Used
Pressure Acting at Entry - (Measured in Pascal) - Pressure Acting at Entry is the force per unit area of Rollers/plates.
Mean Yield Shear Stress at Entry - Mean Yield Shear Stress at Entry represents the average shear stress at which the material begins to yield or undergo plastic deformation.
Thickness at Entry - (Measured in Meter) - Thickness at Entry is defined as the thickness of stock at any point between entry and neutral point.
Initial Thickness - (Measured in Meter) - Initial Thickness or Thickness before Rolling is the thickness of sheet before the rolling operation.
Coefficient of Friction - Coefficient of Friction(μ) is the ratio defining the force that resists the motion of one body in relation to another body in contact with it.
The Roller Radius - (Measured in Meter) - The Roller Radius is the distance between the center and the point on the circumference of the roller.
Final Thickness after Rolling - (Measured in Meter) - Final Thickness after Rolling is the thickness of the workpiece after rolling.
Angle made by Point Roll Center and Normal - (Measured in Radian) - Angle made by Point Roll Center and Normal is a point around which a vehicle's body tends to roll during cornering.
Angle of Bite - (Measured in Radian) - Angle of Bite is the angle made by entry point, roll center and normal.
STEP 1: Convert Input(s) to Base Unit
Mean Yield Shear Stress at Entry: 5896.83 --> No Conversion Required
Thickness at Entry: 0.011 Millimeter --> 1.1E-05 Meter (Check conversion here)
Initial Thickness: 3.5 Millimeter --> 0.0035 Meter (Check conversion here)
Coefficient of Friction: 0.5 --> No Conversion Required
The Roller Radius: 104 Millimeter --> 0.104 Meter (Check conversion here)
Final Thickness after Rolling: 7.5 Millimeter --> 0.0075 Meter (Check conversion here)
Angle made by Point Roll Center and Normal: 19.5 Degree --> 0.34033920413883 Radian (Check conversion here)
Angle of Bite: 45 Degree --> 0.785398163397301 Radian (Check conversion here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
Pe = Se*he/hin*exp(μrp*(2*sqrt(Rroller/hf)*atan(Θr*sqrt(Rroller/hf))-2*sqrt(Rroller/hf)*atan(αbite*sqrt(Rroller/hf)))) --> 5896.83*1.1E-05/0.0035*exp(0.5*(2*sqrt(0.104/0.0075)*atan(0.34033920413883*sqrt(0.104/0.0075))-2*sqrt(0.104/0.0075)*atan(0.785398163397301*sqrt(0.104/0.0075))))
Evaluating ... ...
Pe = 5.2529579404996
STEP 3: Convert Result to Output's Unit
5.2529579404996 Pascal -->5.2529579404996E-06 Newton per Square Millimeter (Check conversion here)
FINAL ANSWER
5.2529579404996E-06 5.3E-6 Newton per Square Millimeter <-- Pressure Acting at Entry
(Calculation completed in 00.004 seconds)

Credits

Created by Rajat Vishwakarma
University Institute of Technology RGPV (UIT - RGPV), Bhopal
Rajat Vishwakarma has created this Calculator and 400+ more calculators!
Verified by Ravi Khiyani
Shri Govindram Seksaria Institute of Technology and Science (SGSITS), Indore
Ravi Khiyani has verified this Calculator and 300+ more calculators!

4 Analysis at Entry Region Calculators

Pressure Acting on Rolls from Entry Side
Go Pressure Acting at Entry = Mean Yield Shear Stress at Entry*Thickness at Entry/Initial Thickness*exp(Coefficient of Friction*(2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle made by Point Roll Center and Normal*sqrt(The Roller Radius/Final Thickness after Rolling))-2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle of Bite*sqrt(The Roller Radius/Final Thickness after Rolling))))
Mean Yield Shear Stress given Pressure on Entry Side
Go Mean Yield Shear Stress at Entry = (Pressure Acting at Entry*Initial Thickness/Thickness at Entry)/(exp(Coefficient of Friction*(Factor H at the Entry Point on Workpiece-Factor H at a given Point on Workpiece)))
Thickness of Stock at given Point on Entry Side
Go Thickness at Entry = (Pressure Acting at Entry*Initial Thickness)/(Mean Yield Shear Stress at Entry*exp(Coefficient of Friction*(Factor H at the Entry Point on Workpiece-Factor H at a given Point on Workpiece)))
Pressure on Rolls given H (Entry Side)
Go Pressure Acting at Entry = Mean Yield Shear Stress at Entry*Thickness at Entry/Initial Thickness*exp(Coefficient of Friction*(Factor H at the Entry Point on Workpiece-Factor H at a given Point on Workpiece))

Pressure Acting on Rolls from Entry Side Formula

Pressure Acting at Entry = Mean Yield Shear Stress at Entry*Thickness at Entry/Initial Thickness*exp(Coefficient of Friction*(2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle made by Point Roll Center and Normal*sqrt(The Roller Radius/Final Thickness after Rolling))-2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle of Bite*sqrt(The Roller Radius/Final Thickness after Rolling))))
Pe = Se*he/hin*exp(μrp*(2*sqrt(Rroller/hf)*atan(Θr*sqrt(Rroller/hf))-2*sqrt(Rroller/hf)*atan(αbite*sqrt(Rroller/hf))))

How does pressure on rolls vary?

The pressure on rolls starts from the entry point and continues to build up till the neutral point. Similarly the exit pressure is zero at the exit point and increases towards the neutral point. At any section i, between the entry point and exit point in the rolls.

How to Calculate Pressure Acting on Rolls from Entry Side?

Pressure Acting on Rolls from Entry Side calculator uses Pressure Acting at Entry = Mean Yield Shear Stress at Entry*Thickness at Entry/Initial Thickness*exp(Coefficient of Friction*(2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle made by Point Roll Center and Normal*sqrt(The Roller Radius/Final Thickness after Rolling))-2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle of Bite*sqrt(The Roller Radius/Final Thickness after Rolling)))) to calculate the Pressure Acting at Entry, The Pressure acting on rolls from entry side formula is such as the pressure on rolls starts from the entry point and continues to build up till the neutral point. Pressure Acting at Entry is denoted by Pe symbol.

How to calculate Pressure Acting on Rolls from Entry Side using this online calculator? To use this online calculator for Pressure Acting on Rolls from Entry Side, enter Mean Yield Shear Stress at Entry (Se), Thickness at Entry (he), Initial Thickness (hin), Coefficient of Friction rp), The Roller Radius (Rroller), Final Thickness after Rolling (hf), Angle made by Point Roll Center and Normal r) & Angle of Bite bite) and hit the calculate button. Here is how the Pressure Acting on Rolls from Entry Side calculation can be explained with given input values -> 5.3E-12 = 5896.83*1.1E-05/0.0035*exp(0.5*(2*sqrt(0.104/0.0075)*atan(0.34033920413883*sqrt(0.104/0.0075))-2*sqrt(0.104/0.0075)*atan(0.785398163397301*sqrt(0.104/0.0075)))).

FAQ

What is Pressure Acting on Rolls from Entry Side?
The Pressure acting on rolls from entry side formula is such as the pressure on rolls starts from the entry point and continues to build up till the neutral point and is represented as Pe = Se*he/hin*exp(μrp*(2*sqrt(Rroller/hf)*atan(Θr*sqrt(Rroller/hf))-2*sqrt(Rroller/hf)*atan(αbite*sqrt(Rroller/hf)))) or Pressure Acting at Entry = Mean Yield Shear Stress at Entry*Thickness at Entry/Initial Thickness*exp(Coefficient of Friction*(2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle made by Point Roll Center and Normal*sqrt(The Roller Radius/Final Thickness after Rolling))-2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle of Bite*sqrt(The Roller Radius/Final Thickness after Rolling)))). Mean Yield Shear Stress at Entry represents the average shear stress at which the material begins to yield or undergo plastic deformation, Thickness at Entry is defined as the thickness of stock at any point between entry and neutral point, Initial Thickness or Thickness before Rolling is the thickness of sheet before the rolling operation, Coefficient of Friction(μ) is the ratio defining the force that resists the motion of one body in relation to another body in contact with it, The Roller Radius is the distance between the center and the point on the circumference of the roller, Final Thickness after Rolling is the thickness of the workpiece after rolling, Angle made by Point Roll Center and Normal is a point around which a vehicle's body tends to roll during cornering & Angle of Bite is the angle made by entry point, roll center and normal.
How to calculate Pressure Acting on Rolls from Entry Side?
The Pressure acting on rolls from entry side formula is such as the pressure on rolls starts from the entry point and continues to build up till the neutral point is calculated using Pressure Acting at Entry = Mean Yield Shear Stress at Entry*Thickness at Entry/Initial Thickness*exp(Coefficient of Friction*(2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle made by Point Roll Center and Normal*sqrt(The Roller Radius/Final Thickness after Rolling))-2*sqrt(The Roller Radius/Final Thickness after Rolling)*atan(Angle of Bite*sqrt(The Roller Radius/Final Thickness after Rolling)))). To calculate Pressure Acting on Rolls from Entry Side, you need Mean Yield Shear Stress at Entry (Se), Thickness at Entry (he), Initial Thickness (hin), Coefficient of Friction rp), The Roller Radius (Rroller), Final Thickness after Rolling (hf), Angle made by Point Roll Center and Normal r) & Angle of Bite bite). With our tool, you need to enter the respective value for Mean Yield Shear Stress at Entry, Thickness at Entry, Initial Thickness, Coefficient of Friction, The Roller Radius, Final Thickness after Rolling, Angle made by Point Roll Center and Normal & Angle of Bite and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
How many ways are there to calculate Pressure Acting at Entry?
In this formula, Pressure Acting at Entry uses Mean Yield Shear Stress at Entry, Thickness at Entry, Initial Thickness, Coefficient of Friction, The Roller Radius, Final Thickness after Rolling, Angle made by Point Roll Center and Normal & Angle of Bite. We can use 1 other way(s) to calculate the same, which is/are as follows -
  • Pressure Acting at Entry = Mean Yield Shear Stress at Entry*Thickness at Entry/Initial Thickness*exp(Coefficient of Friction*(Factor H at the Entry Point on Workpiece-Factor H at a given Point on Workpiece))
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!