Voltage Reflection Coefficient of Tunnel Diode Solution

STEP 0: Pre-Calculation Summary
Formula Used
Voltage Reflection Coefficient = (Impedance Tunnel Diode-Characteristic Impedance)/(Impedance Tunnel Diode+Characteristic Impedance)
Γ = (Zd-Zo)/(Zd+Zo)
This formula uses 3 Variables
Variables Used
Voltage Reflection Coefficient - Voltage Reflection Coefficient depends on the load impedance and the impedance of the transmission line or circuit it is connected to.
Impedance Tunnel Diode - (Measured in Ohm) - Impedance Tunnel Diode is a complex quantity that depends on the operating conditions of the device.
Characteristic Impedance - (Measured in Ohm) - Characteristic Impedance s a measure of its ability to carry electrical signals with minimal distortion.
STEP 1: Convert Input(s) to Base Unit
Impedance Tunnel Diode: 65 Ohm --> 65 Ohm No Conversion Required
Characteristic Impedance: 50 Ohm --> 50 Ohm No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
Γ = (Zd-Zo)/(Zd+Zo) --> (65-50)/(65+50)
Evaluating ... ...
Γ = 0.130434782608696
STEP 3: Convert Result to Output's Unit
0.130434782608696 --> No Conversion Required
FINAL ANSWER
0.130434782608696 0.130435 <-- Voltage Reflection Coefficient
(Calculation completed in 00.004 seconds)

Credits

Created by Shobhit Dimri
Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat
Shobhit Dimri has created this Calculator and 900+ more calculators!
Verified by Urvi Rathod
Vishwakarma Government Engineering College (VGEC), Ahmedabad
Urvi Rathod has verified this Calculator and 1900+ more calculators!

16 Non Linear Circuits Calculators

Room Temperature
Go Ambient Temperature = (2*Diode Temperature*((1/(Coupling Coefficient*Q Factor))+(1/((Coupling Coefficient*Q Factor)^2) )))/(Noise Figure of Up-Converter-1)
Average Diode Temperature using Single Side Band Noise
Go Diode Temperature = (Noise Figure of Single Side Band-2)*((Output Resistance of Signal Generator*Ambient Temperature)/(2*Diode Resistance))
Noise Figure of Single Side Band
Go Noise Figure of Single Side Band = 2+((2*Diode Temperature*Diode Resistance)/(Output Resistance of Signal Generator*Ambient Temperature))
Noise Figure of Double Side Band
Go Noise Figure of Double Side Band = 1+((Diode Temperature*Diode Resistance)/(Output Resistance of Signal Generator*Ambient Temperature))
Voltage Reflection Coefficient of Tunnel Diode
Go Voltage Reflection Coefficient = (Impedance Tunnel Diode-Characteristic Impedance)/(Impedance Tunnel Diode+Characteristic Impedance)
Amplifier Gain of Tunnel Diode
Go Amplifier Gain of Tunnel Diode = Negative Resistance in Tunnel Diode/(Negative Resistance in Tunnel Diode-Load Resistance)
Ratio Negative Resistance to Series Resistance
Go Ratio Negative Resistance to Series Resistance = Equivalent Negative Resistance/Total Series Resistance at Idler Frequency
Tunnel Diode Output Power
Go Output Power of Tunnel Diode = (Voltage Tunnel Diode*Current Tunnel Diode)/(2*pi)
Bandwidth using Dynamic Quality Factor
Go Bandwidth = Dynamic Q-Factor/(Angular Frequency*Series Resistance of Diode)
Dynamic Q Factor
Go Dynamic Q-Factor = Bandwidth/(Angular Frequency*Series Resistance of Diode)
Maximum Applied Current across Diode
Go Maximum Applied Current = Maximum Applied Voltage/Reactive Impedence
Reactive Impedence
Go Reactive Impedence = Maximum Applied Voltage/Maximum Applied Current
Maximum Applied Voltage across Diode
Go Maximum Applied Voltage = Maximum Electric Field*Depletion Length
Negative Conductance of Tunnel Diode
Go Negative Conductance Tunnel Diode = 1/(Negative Resistance in Tunnel Diode)
Magnitude of Negative Resistance
Go Negative Resistance in Tunnel Diode = 1/(Negative Conductance Tunnel Diode)
Power Gain of Tunnel Diode
Go Power Gain of Tunnel Diode = Voltage Reflection Coefficient^2

Voltage Reflection Coefficient of Tunnel Diode Formula

Voltage Reflection Coefficient = (Impedance Tunnel Diode-Characteristic Impedance)/(Impedance Tunnel Diode+Characteristic Impedance)
Γ = (Zd-Zo)/(Zd+Zo)

What is Tunnel Diode?

A tunnel diode (also known as a Esaki diode) is a type of semiconductor diode that has effectively “negative resistance” due to the quantum mechanical effect called tunneling. Tunnel diodes have a heavily doped pn junction that is about 10 nm wide.

How to Calculate Voltage Reflection Coefficient of Tunnel Diode?

Voltage Reflection Coefficient of Tunnel Diode calculator uses Voltage Reflection Coefficient = (Impedance Tunnel Diode-Characteristic Impedance)/(Impedance Tunnel Diode+Characteristic Impedance) to calculate the Voltage Reflection Coefficient, Voltage Reflection Coefficient of Tunnel Diode depends on the load impedance and the impedance of the transmission line or circuit it is connected to. When a tunnel diode is used as an amplifier or oscillator, it is often connected to a transmission line or a resonant circuit. Voltage Reflection Coefficient is denoted by Γ symbol.

How to calculate Voltage Reflection Coefficient of Tunnel Diode using this online calculator? To use this online calculator for Voltage Reflection Coefficient of Tunnel Diode, enter Impedance Tunnel Diode (Zd) & Characteristic Impedance (Zo) and hit the calculate button. Here is how the Voltage Reflection Coefficient of Tunnel Diode calculation can be explained with given input values -> 0.130435 = (65-50)/(65+50).

FAQ

What is Voltage Reflection Coefficient of Tunnel Diode?
Voltage Reflection Coefficient of Tunnel Diode depends on the load impedance and the impedance of the transmission line or circuit it is connected to. When a tunnel diode is used as an amplifier or oscillator, it is often connected to a transmission line or a resonant circuit and is represented as Γ = (Zd-Zo)/(Zd+Zo) or Voltage Reflection Coefficient = (Impedance Tunnel Diode-Characteristic Impedance)/(Impedance Tunnel Diode+Characteristic Impedance). Impedance Tunnel Diode is a complex quantity that depends on the operating conditions of the device & Characteristic Impedance s a measure of its ability to carry electrical signals with minimal distortion.
How to calculate Voltage Reflection Coefficient of Tunnel Diode?
Voltage Reflection Coefficient of Tunnel Diode depends on the load impedance and the impedance of the transmission line or circuit it is connected to. When a tunnel diode is used as an amplifier or oscillator, it is often connected to a transmission line or a resonant circuit is calculated using Voltage Reflection Coefficient = (Impedance Tunnel Diode-Characteristic Impedance)/(Impedance Tunnel Diode+Characteristic Impedance). To calculate Voltage Reflection Coefficient of Tunnel Diode, you need Impedance Tunnel Diode (Zd) & Characteristic Impedance (Zo). With our tool, you need to enter the respective value for Impedance Tunnel Diode & Characteristic Impedance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!