Slip of Scherbius Drive given RMS Line Voltage Solution

STEP 0: Pre-Calculation Summary
Formula Used
Slip = (Back Emf/RMS Value of Rotor Side Line Voltage)*modulus(cos(Firing Angle))
s = (Eb/Er)*modulus(cos(θ))
This formula uses 2 Functions, 4 Variables
Functions Used
cos - Cosine of an angle is the ratio of the side adjacent to the angle to the hypotenuse of the triangle., cos(Angle)
modulus - Modulus of a number is the remainder when that number is divided by another number., modulus
Variables Used
Slip - Slip Energy Recovery is one of the methods of controlling the speed of an Induction motor.
Back Emf - (Measured in Volt) - Back emf the back emf is calculated based on the difference between the supplied voltage and the loss from the current through the resistance.
RMS Value of Rotor Side Line Voltage - (Measured in Volt) - RMS value of Rotor side line voltage in static scherbius drive. RMS value (root mean square) stands for the square root of means of squares of instantaneous values.
Firing Angle - (Measured in Radian) - Firing angle α. It is defined as angle measured from the instant that gives. maximum output voltage to the one at which it is actually triggered.
STEP 1: Convert Input(s) to Base Unit
Back Emf: 145 Volt --> 145 Volt No Conversion Required
RMS Value of Rotor Side Line Voltage: 156 Volt --> 156 Volt No Conversion Required
Firing Angle: 26 Degree --> 0.45378560551844 Radian (Check conversion here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
s = (Eb/Er)*modulus(cos(θ)) --> (145/156)*modulus(cos(0.45378560551844))
Evaluating ... ...
s = 0.835417543034517
STEP 3: Convert Result to Output's Unit
0.835417543034517 --> No Conversion Required
FINAL ANSWER
0.835417543034517 0.835418 <-- Slip
(Calculation completed in 00.004 seconds)

Credits

Created by Aman Dhussawat
GURU TEGH BAHADUR INSTITUTE OF TECHNOLOGY (GTBIT), NEW DELHI
Aman Dhussawat has created this Calculator and 50+ more calculators!
Verified by Parminder Singh
Chandigarh University (CU), Punjab
Parminder Singh has verified this Calculator and 600+ more calculators!

10+ Electric Drives Calculators

Torque of Squirrel Cage Induction Motor
Go Torque = (Constant*Voltage^2*Rotor Resistance) /((Stator Resistance+Rotor Resistance)^2+(Stator Reactance+Rotor Reactance)^2)
Torque Generated by Scherbius Drive
Go Torque = 1.35*((Back Emf*AC Line Voltage*Rectified Rotor Current*RMS Value of Rotor Side Line Voltage)/(Back Emf*Angular Frequency))
Time Taken for Drive Speed
Go Time Taken for Drive Speed = Moment of Inertia*int(1/(Torque-Load Torque),x,Initial angular Velocity,Final Angular Velocity)
Energy Dissipated during Transient Operation
Go Energy Dissipated in Transient Operation = int(Resistance of Motor Winding*(Electric Current)^2,x,0,Time Period)
Slip of Scherbius Drive given RMS Line Voltage
Go Slip = (Back Emf/RMS Value of Rotor Side Line Voltage)*modulus(cos(Firing Angle))
DC Output Voltage of Rectifier in Scherbius Drive Given Rotor RMS Line Voltage
Go DC Voltage = (3*sqrt(2))*(RMS Value of Rotor Side Line Voltage/pi)
Gear Tooth Ratio
Go Gear Tooth Ratio = Number 1 of Teeth of Driving Gear/Number 2 of Teeth of Driven Gear
Average Back Emf with Negligible Commutation Overlap
Go Back Emf = 1.35*AC Line Voltage*cos(Firing Angle)
DC Output Voltage of Rectifier in Scherbius Drive Given Rotor RMS Line Voltage at Slip
Go DC Voltage = 1.35*RMS Value of Rotor Side Line Voltage with Slip
DC Output Voltage of Rectifier in Scherbius Drive Given Maximum Rotor Voltage
Go DC Voltage = 3*(Peak Voltage/pi)

15 Traction Physics Calculators

Tractive Effort on Driven Wheel
Go Wheel Tractive Effort = (Gear Ratio of Transmission*Gear Ratio of Final Drive*(Efficiency of Driveline/100)*Torque Output from Powerplant)/Effective Radius of Wheel
Energy Available during Regeneration
Go Energy Consumption during Regeneration = 0.01072*(Accelerating Weight of Train/Weight of Train)*(Final Velocity^2-Initial Velocity^2)
Tractive Effort during Acceleration
Go Acceleration Tractive Effort = (277.8*Accelerating Weight of Train*Acceleration of Train)+(Weight of Train*Specific Resistance Train)
Slip of Scherbius Drive given RMS Line Voltage
Go Slip = (Back Emf/RMS Value of Rotor Side Line Voltage)*modulus(cos(Firing Angle))
Tractive Effort Required while going down Gradient
Go Down Gradient Tractive Effort = (Weight of Train*Specific Resistance Train)-(98.1*Weight of Train*Gradient)
Tractive Effort Required during Free-Running
Go Free Run Tractive Effort = (98.1*Weight of Train*Gradient)+(Weight of Train*Specific Resistance Train)
Total Tractive Effort Required for Propulsion of Train
Go Train Tractive Effort = Resistance Overcome Tractive Effort+Gravity Overcome Tractive Effort+Force
Tractive Effort Required to Overcome Effect of Gravity
Go Gravity Tractive Effort = 1000*Weight of Train*[g]*sin(Angle D)
Tractive Effort at Wheel
Go Wheel Tractive Effort = (Pinion Edge Tractive Effort*Diameter of Pinion 2)/Diameter of Wheel
Energy Consumption for Overcoming Gradient and Tracking Resistance
Go Energy Consumption for Overcoming Gradient = Tractive Effort*Velocity*Time Taken by Train
Power Output of Motor using Efficiency of Gear Transmission
Go Power Output Train = (Tractive Effort*Velocity)/(3600*Gear Efficiency)
Tractive Effort Required for Linear and Angular Acceleration
Go Angular Accelration Tractive Effort = 27.88*Weight of Train*Acceleration of Train
Tractive Effort Required to Overcome Train Resistance
Go Resistance Overcome Tractive Effort = Specific Resistance Train*Weight of Train
Tractive Effort at Edge of Pinion
Go Pinion Edge Tractive Effort = (2*Engine Torque)/Diameter of Pinion 1
Tractive Effort Required to Overcome Effect of Gravity given Gradient during up Gradient
Go Tractive Effort of Up Gradient = 98.1*Weight of Train*Gradient

Slip of Scherbius Drive given RMS Line Voltage Formula

Slip = (Back Emf/RMS Value of Rotor Side Line Voltage)*modulus(cos(Firing Angle))
s = (Eb/Er)*modulus(cos(θ))

What is slip power?

The slip power recovery (SPR) drive is an external system connected to the rotor circuit in place of the external resistors. The SPR provides speed and torque control like the resistors but can also recover the power taken off the rotor and feed it back into the power system to avoid energy waste.

How to Calculate Slip of Scherbius Drive given RMS Line Voltage?

Slip of Scherbius Drive given RMS Line Voltage calculator uses Slip = (Back Emf/RMS Value of Rotor Side Line Voltage)*modulus(cos(Firing Angle)) to calculate the Slip, The Slip of Scherbius Drive given RMS Line Voltage formula is defined as neglecting the drop across the inductor. Slip is denoted by s symbol.

How to calculate Slip of Scherbius Drive given RMS Line Voltage using this online calculator? To use this online calculator for Slip of Scherbius Drive given RMS Line Voltage, enter Back Emf (Eb), RMS Value of Rotor Side Line Voltage (Er) & Firing Angle (θ) and hit the calculate button. Here is how the Slip of Scherbius Drive given RMS Line Voltage calculation can be explained with given input values -> 0.835418 = (145/156)*modulus(cos(0.45378560551844)).

FAQ

What is Slip of Scherbius Drive given RMS Line Voltage?
The Slip of Scherbius Drive given RMS Line Voltage formula is defined as neglecting the drop across the inductor and is represented as s = (Eb/Er)*modulus(cos(θ)) or Slip = (Back Emf/RMS Value of Rotor Side Line Voltage)*modulus(cos(Firing Angle)). Back emf the back emf is calculated based on the difference between the supplied voltage and the loss from the current through the resistance, RMS value of Rotor side line voltage in static scherbius drive. RMS value (root mean square) stands for the square root of means of squares of instantaneous values & Firing angle α. It is defined as angle measured from the instant that gives. maximum output voltage to the one at which it is actually triggered.
How to calculate Slip of Scherbius Drive given RMS Line Voltage?
The Slip of Scherbius Drive given RMS Line Voltage formula is defined as neglecting the drop across the inductor is calculated using Slip = (Back Emf/RMS Value of Rotor Side Line Voltage)*modulus(cos(Firing Angle)). To calculate Slip of Scherbius Drive given RMS Line Voltage, you need Back Emf (Eb), RMS Value of Rotor Side Line Voltage (Er) & Firing Angle (θ). With our tool, you need to enter the respective value for Back Emf, RMS Value of Rotor Side Line Voltage & Firing Angle and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!