Thickness of Plate given Axial Load on Weld Solution

STEP 0: Pre-Calculation Summary
Formula Used
Thickness of Plate = Axial Load on Weld/(Shear Stress*(Length of Top Weld+Length of Bottom Weld)*0.707)
tplate = Pweld/(๐œ*(Ltop weld+L2)*0.707)
This formula uses 5 Variables
Variables Used
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.
Axial Load on Weld - (Measured in Newton) - Axial Load on Weld is defined as applying a force on a structure directly along an axis of the structure.
Shear Stress - (Measured in Pascal) - Shear Stress is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress.
Length of Top Weld - (Measured in Meter) - Length of top weld is the linear distance of each weld segment.
Length of Bottom Weld - (Measured in Meter) - Length of bottom weld is the linear distance of each weld segment.
STEP 1: Convert Input(s) to Base Unit
Axial Load on Weld: 9.6 Kilonewton --> 9600 Newton (Check conversion here)
Shear Stress: 2.4 Megapascal --> 2400000 Pascal (Check conversion here)
Length of Top Weld: 4 Millimeter --> 0.004 Meter (Check conversion here)
Length of Bottom Weld: 6 Millimeter --> 0.006 Meter (Check conversion here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
tplate = Pweld/(๐œ*(Ltop weld+L2)*0.707) --> 9600/(2400000*(0.004+0.006)*0.707)
Evaluating ... ...
tplate = 0.565770862800566
STEP 3: Convert Result to Output's Unit
0.565770862800566 Meter -->565.770862800566 Millimeter (Check conversion here)
FINAL ANSWER
565.770862800566 โ‰ˆ 565.7709 Millimeter <-- Thickness of Plate
(Calculation completed in 00.004 seconds)

Credits

Created by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has created this Calculator and 2000+ more calculators!
Verified by Payal Priya
Birsa Institute of Technology (BIT), Sindri
Payal Priya has verified this Calculator and 1900+ more calculators!

20 Analysis of Unsymmetrical Welded Sections which are Loaded Axially Calculators

Total Length of Weld given Resistance of Bottom Weld
Go Total length of weld = (Resistance of bottom weld*(Distance of top weld from gravity axis+Distance of Bottom Weld from Gravity Axis))/(Resistance of weld per unit length*Distance of top weld from gravity axis)
Total Length of Weld given Resistance of Top Weld
Go Total length of weld = (Resistance of top weld*(Distance of top weld from gravity axis+Distance of Bottom Weld from Gravity Axis))/(Resistance of weld per unit length*Distance of Bottom Weld from Gravity Axis)
Total Resistance given Resistance of Bottom Weld
Go Total resistance = (Resistance of bottom weld*(Distance of top weld from gravity axis+Distance of Bottom Weld from Gravity Axis))/(Distance of top weld from gravity axis)
Total Resistance given Resistance of Top Weld
Go Total resistance = (Resistance of top weld*(Distance of top weld from gravity axis+Distance of Bottom Weld from Gravity Axis))/(Distance of Bottom Weld from Gravity Axis)
Total Length of Weld given Length of Top Weld
Go Total length of weld = (Length of Top Weld*(Distance of top weld from gravity axis+Distance of Bottom Weld from Gravity Axis))/Distance of Bottom Weld from Gravity Axis
Total Length of Weld given Length of Bottom Weld
Go Total length of weld = (Length of Top Weld*(Distance of top weld from gravity axis+Distance of Bottom Weld from Gravity Axis))/Distance of top weld from gravity axis
Shear Stress given Axial Load on Welded Connection
Go Shear Stress = Axial Load on Weld/((Length of Top Weld+Length of Bottom Weld)*0.707*Thickness of Plate)
Thickness of Plate given Axial Load on Weld
Go Thickness of Plate = Axial Load on Weld/(Shear Stress*(Length of Top Weld+Length of Bottom Weld)*0.707)
Axial Load on Weld
Go Axial Load on Weld = Shear Stress*(Length of Top Weld+Length of Bottom Weld)*0.707*Thickness of Plate
Axial Load on Angle
Go Axial load on angle = Resistance of weld per unit length*(Length of Top Weld+Length of Bottom Weld)
Thickness of Plate given Area of Unsymmetrical Weld
Go Thickness of Plate = Weld Bed Area/((Length of Top Weld+Length of Bottom Weld)*0.707)
Area of Unsymmetrical Weld
Go Weld Bed Area = (Length of Top Weld+Length of Bottom Weld)*0.707*Thickness of Plate
Axial Load on Angle given Resistance of Bottom and Top Weld
Go Axial load on angle = Resistance of top weld+Resistance of bottom weld
Total Length of Weld given Length of Top and Bottom Weld
Go Total length of weld = Length of Top Weld+Length of Bottom Weld
Total Length of Weld given Area of Unsymmetrical Weld
Go Total length of weld = Weld Bed Area/(Throat Thickness)
Throat Thickness given Area of Unsymmetrical Weld
Go Throat Thickness = Weld Bed Area/(Total length of weld)
Area of Unsymmetrical Weld given Throat Thickness
Go Weld Bed Area = Total length of weld*Throat Thickness
Shear Stress given Axial Load on Weld
Go Shear Stress = Axial Load on Weld/(Weld Bed Area)
Axial Load on Weld given Shear Stress
Go Axial Load on Weld = Shear Stress*Weld Bed Area
Area of Weld given Axial Load on Weld
Go Weld Bed Area = Axial Load on Weld/Shear Stress

Thickness of Plate given Axial Load on Weld Formula

Thickness of Plate = Axial Load on Weld/(Shear Stress*(Length of Top Weld+Length of Bottom Weld)*0.707)
tplate = Pweld/(๐œ*(Ltop weld+L2)*0.707)

What is axial load and radial load?

Radial Load is defined as the maximum force that can be applied to the shaft in the radial direction (any direction perpendicular to the motor shaft axis). Axial Load is defined as the maximum force that can be applied to the shaft in the axial direction (in the same axis as or parallel to the motor shaft axis).

How to Calculate Thickness of Plate given Axial Load on Weld?

Thickness of Plate given Axial Load on Weld calculator uses Thickness of Plate = Axial Load on Weld/(Shear Stress*(Length of Top Weld+Length of Bottom Weld)*0.707) to calculate the Thickness of Plate, The Thickness of plate given axial load on weld is defined as the distance through an object, as distinct from width or height. Thickness of Plate is denoted by tplate symbol.

How to calculate Thickness of Plate given Axial Load on Weld using this online calculator? To use this online calculator for Thickness of Plate given Axial Load on Weld, enter Axial Load on Weld (Pweld), Shear Stress (๐œ), Length of Top Weld (Ltop weld) & Length of Bottom Weld (L2) and hit the calculate button. Here is how the Thickness of Plate given Axial Load on Weld calculation can be explained with given input values -> 565770.9 = 9600/(2400000*(0.004+0.006)*0.707).

FAQ

What is Thickness of Plate given Axial Load on Weld?
The Thickness of plate given axial load on weld is defined as the distance through an object, as distinct from width or height and is represented as tplate = Pweld/(๐œ*(Ltop weld+L2)*0.707) or Thickness of Plate = Axial Load on Weld/(Shear Stress*(Length of Top Weld+Length of Bottom Weld)*0.707). Axial Load on Weld is defined as applying a force on a structure directly along an axis of the structure, Shear Stress is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress, Length of top weld is the linear distance of each weld segment & Length of bottom weld is the linear distance of each weld segment.
How to calculate Thickness of Plate given Axial Load on Weld?
The Thickness of plate given axial load on weld is defined as the distance through an object, as distinct from width or height is calculated using Thickness of Plate = Axial Load on Weld/(Shear Stress*(Length of Top Weld+Length of Bottom Weld)*0.707). To calculate Thickness of Plate given Axial Load on Weld, you need Axial Load on Weld (Pweld), Shear Stress (๐œ), Length of Top Weld (Ltop weld) & Length of Bottom Weld (L2). With our tool, you need to enter the respective value for Axial Load on Weld, Shear Stress, Length of Top Weld & Length of Bottom Weld and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
How many ways are there to calculate Thickness of Plate?
In this formula, Thickness of Plate uses Axial Load on Weld, Shear Stress, Length of Top Weld & Length of Bottom Weld. We can use 1 other way(s) to calculate the same, which is/are as follows -
  • Thickness of Plate = Weld Bed Area/((Length of Top Weld+Length of Bottom Weld)*0.707)
Let Others Know
โœ–
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!