Total Maximum Discharge for Total of all Inlets Solution

STEP 0: Pre-Calculation Summary
Formula Used
Maximum Discharge of Total Inlets = (2*pi*Ocean Tide Amplitude*Surface Area of Bay*Maximum Velocity in the Inlet Throat)/Tidal Period
Qmax = (2*pi*ao*Ab*Vmax)/T
This formula uses 1 Constants, 5 Variables
Constants Used
pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288
Variables Used
Maximum Discharge of Total Inlets - (Measured in Cubic Meter per Second) - Maximum Discharge of Total Inlets is the maximum volume flow rate passing a particular location during an event.
Ocean Tide Amplitude - (Measured in Meter) - Ocean Tide Amplitude is the height difference between high and low tides, reflecting gravitational forces from the moon and sun.
Surface Area of Bay - (Measured in Square Meter) - Surface Area of Bay is defined as a small body of water set off from the main body.
Maximum Velocity in the Inlet Throat - (Measured in Meter per Second) - Maximum Velocity in the Inlet Throat [length/time] is measure of speed in the inlet throat.
Tidal Period - (Measured in Second) - Tidal Period is an efficient way of guesstimating how much water there is, at any given time of day, over a particular point.
STEP 1: Convert Input(s) to Base Unit
Ocean Tide Amplitude: 4 Meter --> 4 Meter No Conversion Required
Surface Area of Bay: 1.5001 Square Meter --> 1.5001 Square Meter No Conversion Required
Maximum Velocity in the Inlet Throat: 35 Meter per Second --> 35 Meter per Second No Conversion Required
Tidal Period: 130 Second --> 130 Second No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
Qmax = (2*pi*ao*Ab*Vmax)/T --> (2*pi*4*1.5001*35)/130
Evaluating ... ...
Qmax = 10.1504375315539
STEP 3: Convert Result to Output's Unit
10.1504375315539 Cubic Meter per Second --> No Conversion Required
FINAL ANSWER
10.1504375315539 10.15044 Cubic Meter per Second <-- Maximum Discharge of Total Inlets
(Calculation completed in 00.004 seconds)

Credits

Created by Mithila Muthamma PA
Coorg Institute of Technology (CIT), Coorg
Mithila Muthamma PA has created this Calculator and 2000+ more calculators!
Verified by M Naveen
National Institute of Technology (NIT), Warangal
M Naveen has verified this Calculator and 900+ more calculators!

5 Multiple Inlets Calculators

Ocean Tide Amplitude given Total Maximum Discharge for Total of all Inlets
Go Ocean Tide Amplitude = (Maximum Discharge of Total Inlets*Tidal Period)/(2*pi*Surface Area of Bay*Maximum Velocity in the Inlet Throat)
Maximum Velocity in Inlet Throat given Total Maximum Discharge
Go Maximum Velocity in the Inlet Throat = (Maximum Discharge of Total Inlets*Tidal Period)/(2*pi*Ocean Tide Amplitude*Surface Area of Bay)
Surface Area of Bay or Basin given Total Maximum Discharge
Go Surface Area of Bay = (Maximum Discharge of Total Inlets*Tidal Period)/(2*pi*Ocean Tide Amplitude*Maximum Velocity in the Inlet Throat)
Tidal Period given Total Maximum Discharge for Total of all Inlets
Go Tidal Period = (2*pi*Ocean Tide Amplitude*Maximum Velocity in the Inlet Throat*Surface Area of Bay)/Maximum Discharge of Total Inlets
Total Maximum Discharge for Total of all Inlets
Go Maximum Discharge of Total Inlets = (2*pi*Ocean Tide Amplitude*Surface Area of Bay*Maximum Velocity in the Inlet Throat)/Tidal Period

Total Maximum Discharge for Total of all Inlets Formula

Maximum Discharge of Total Inlets = (2*pi*Ocean Tide Amplitude*Surface Area of Bay*Maximum Velocity in the Inlet Throat)/Tidal Period
Qmax = (2*pi*ao*Ab*Vmax)/T

What is Bay Superelevation?

A Superelevation of the bay means that the average level of the bay is greater than the average elevation of the ocean over a given time period. An obvious cause of this effect is the introduction of fresh water into the bay from local rivers and streams. The effect of long-term (months or years) rise in sea level causing a long-term rise in bay level is not included in this definition of bay superelevation, since both sea and bay are responding simultaneously. The bay may not rise at the same rate as the sea due to possible
circulation effects if multiple inlets connect the bay to the ocean.

How to Calculate Total Maximum Discharge for Total of all Inlets?

Total Maximum Discharge for Total of all Inlets calculator uses Maximum Discharge of Total Inlets = (2*pi*Ocean Tide Amplitude*Surface Area of Bay*Maximum Velocity in the Inlet Throat)/Tidal Period to calculate the Maximum Discharge of Total Inlets, The Total Maximum Discharge for Total of all Inlets is defined as the maximum allowable flow rate from all inlets combined. Maximum Discharge of Total Inlets is denoted by Qmax symbol.

How to calculate Total Maximum Discharge for Total of all Inlets using this online calculator? To use this online calculator for Total Maximum Discharge for Total of all Inlets, enter Ocean Tide Amplitude (ao), Surface Area of Bay (Ab), Maximum Velocity in the Inlet Throat (Vmax) & Tidal Period (T) and hit the calculate button. Here is how the Total Maximum Discharge for Total of all Inlets calculation can be explained with given input values -> 10.14976 = (2*pi*4*1.5001*35)/130.

FAQ

What is Total Maximum Discharge for Total of all Inlets?
The Total Maximum Discharge for Total of all Inlets is defined as the maximum allowable flow rate from all inlets combined and is represented as Qmax = (2*pi*ao*Ab*Vmax)/T or Maximum Discharge of Total Inlets = (2*pi*Ocean Tide Amplitude*Surface Area of Bay*Maximum Velocity in the Inlet Throat)/Tidal Period. Ocean Tide Amplitude is the height difference between high and low tides, reflecting gravitational forces from the moon and sun, Surface Area of Bay is defined as a small body of water set off from the main body, Maximum Velocity in the Inlet Throat [length/time] is measure of speed in the inlet throat & Tidal Period is an efficient way of guesstimating how much water there is, at any given time of day, over a particular point.
How to calculate Total Maximum Discharge for Total of all Inlets?
The Total Maximum Discharge for Total of all Inlets is defined as the maximum allowable flow rate from all inlets combined is calculated using Maximum Discharge of Total Inlets = (2*pi*Ocean Tide Amplitude*Surface Area of Bay*Maximum Velocity in the Inlet Throat)/Tidal Period. To calculate Total Maximum Discharge for Total of all Inlets, you need Ocean Tide Amplitude (ao), Surface Area of Bay (Ab), Maximum Velocity in the Inlet Throat (Vmax) & Tidal Period (T). With our tool, you need to enter the respective value for Ocean Tide Amplitude, Surface Area of Bay, Maximum Velocity in the Inlet Throat & Tidal Period and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!