Transverse Shrinkage in First Pass given Total Shrinkage Solution

STEP 0: Pre-Calculation Summary
Formula Used
Transverse Shrinkage in First Pass = Total Transverse Shrinkage-Constant for Multi-Pass Shrinkage*(log10(Total Weight of Weld Metal Deposited/Weld Metal Deposited in First Pass))
S0 = St-b*(log10(w/w0))
This formula uses 1 Functions, 5 Variables
Functions Used
log10 - The common logarithm, also known as the base-10 logarithm or the decimal logarithm, is a mathematical function that is the inverse of the exponential function., log10(Number)
Variables Used
Transverse Shrinkage in First Pass - (Measured in Meter) - Transverse Shrinkage in First Pass is transverse shrinkage in the first pass of welding.
Total Transverse Shrinkage - (Measured in Meter) - Total Transverse shrinkage is the amount by which weldment shrinks due to multiple passes.
Constant for Multi-Pass Shrinkage - Constant for Multi-Pass Shrinkage is used for calculating total transverse shrinkage due to multi-pass welding.
Total Weight of Weld Metal Deposited - (Measured in Kilogram) - Total Weight of Weld Metal Deposited is the amount of metal deposited during welding.
Weld Metal Deposited in First Pass - (Measured in Kilogram) - Weld Metal Deposited in First Pass is just metal deposited in single pass of welding.
STEP 1: Convert Input(s) to Base Unit
Total Transverse Shrinkage: 5.3 Millimeter --> 0.0053 Meter (Check conversion here)
Constant for Multi-Pass Shrinkage: 0.24 --> No Conversion Required
Total Weight of Weld Metal Deposited: 5.15 Gram --> 0.00515 Kilogram (Check conversion here)
Weld Metal Deposited in First Pass: 4.99 Gram --> 0.00499 Kilogram (Check conversion here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
S0 = St-b*(log10(w/w0)) --> 0.0053-0.24*(log10(0.00515/0.00499))
Evaluating ... ...
S0 = 0.00201039597972773
STEP 3: Convert Result to Output's Unit
0.00201039597972773 Meter -->2.01039597972773 Millimeter (Check conversion here)
FINAL ANSWER
2.01039597972773 2.010396 Millimeter <-- Transverse Shrinkage in First Pass
(Calculation completed in 00.020 seconds)

Credits

Created by Rajat Vishwakarma
University Institute of Technology RGPV (UIT - RGPV), Bhopal
Rajat Vishwakarma has created this Calculator and 400+ more calculators!
Verified by Nishan Poojary
Shri Madhwa Vadiraja Institute of Technology and Management (SMVITM), Udupi
Nishan Poojary has verified this Calculator and 400+ more calculators!

14 Butt Joints Calculators

Total transverse shrinkage during multi-pass welding of butt joint
Go Total Transverse Shrinkage = Transverse Shrinkage in First Pass+Constant for Multi-Pass Shrinkage*(log10(Total Weight of Weld Metal Deposited/Weld Metal Deposited in First Pass))
Transverse Shrinkage in First Pass given Total Shrinkage
Go Transverse Shrinkage in First Pass = Total Transverse Shrinkage-Constant for Multi-Pass Shrinkage*(log10(Total Weight of Weld Metal Deposited/Weld Metal Deposited in First Pass))
Metal Deposited in First Pass of Welding given Transverse Shrinkage
Go Weld Metal Deposited in First Pass = Total Weight of Weld Metal Deposited/(10^((Total Transverse Shrinkage-Transverse Shrinkage in First Pass)/Constant for Multi-Pass Shrinkage))
Total Metal Deposited in Weld given Total Transverse Shrinkage
Go Total Weight of Weld Metal Deposited = Weld Metal Deposited in First Pass*(10^((Total Transverse Shrinkage-Transverse Shrinkage in First Pass)/Constant for Multi-Pass Shrinkage))
Plate thickness for given transverse shrinkage in butt joints
Go Plate Thickness = (5.08*Cross‑Sectional Area of Weld)/(Transverse Shrinkage of Butt Joint-(1.27*Root Opening))
Transverse Shrinkage in Butt Joints
Go Transverse Shrinkage of Butt Joint = (5.08*(Cross‑Sectional Area of Weld/Plate Thickness))+(1.27*Root Opening)
Cross-sectional area of weld for given transverse shrinkage in butt joints
Go Cross‑Sectional Area of Weld = (Plate Thickness*(Transverse Shrinkage of Butt Joint-1.27*Root Opening))/5.08
Root Opening given Transverse Shrinkage
Go Root Opening = (Transverse Shrinkage of Butt Joint-5.08*(Cross‑Sectional Area of Weld/Plate Thickness))/1.27
Degree of restraint (Butt joints)
Go Degree of Restraint = ((1000/86)*((Transverse Shrinkage of Unrestrained Joint/Transverse Shrinkage of Restrained Joint)-1))^(1/0.87)
Shrinkage of unrestrained joint from given shrinkage of restrained Butt joint
Go Transverse Shrinkage of Unrestrained Joint = Transverse Shrinkage of Restrained Joint*(1+0.086*Degree of Restraint^0.87)
Transverse shrinkage of restrained joint
Go Transverse Shrinkage of Restrained Joint = Transverse Shrinkage of Unrestrained Joint/(1+0.086*Degree of Restraint^0.87)
Depth of first V-groove for minimum distortion of Butt joint
Go Depth of the First V‑Groove = (0.62*Depth of the Last V‑groove+0.12*Depth of Root Face)/0.38
Depth of last V-groove for minimum distortion of Butt joint
Go Depth of the Last V‑groove = (0.38*Depth of the First V‑Groove-0.12*Depth of Root Face)/0.62
Depth of root face for minimum distortion of Butt joint
Go Depth of Root Face = (0.38*Depth of the First V‑Groove-0.62*Depth of the Last V‑groove)/0.12

Transverse Shrinkage in First Pass given Total Shrinkage Formula

Transverse Shrinkage in First Pass = Total Transverse Shrinkage-Constant for Multi-Pass Shrinkage*(log10(Total Weight of Weld Metal Deposited/Weld Metal Deposited in First Pass))
S0 = St-b*(log10(w/w0))

What is called Distortion in welding terms ?

One of the major problems found with weldments is the distortion. Distortion is caused mainly because of the shrinkage that take place in weldments. The shrinkage taking place in a weldment depends upon the geometry and type of the weld. There are three types of distortions possible in weldments.

(a) Transverse shrinkage occurring perpendicular to the weld line.
(b) Longitudinal shrinkage occurring parallel to the weld line, which is very small of the order of about 0.1% of the weld length and hence can be neglected.
(c) Angular change as a rotation about the weld line.

How to Calculate Transverse Shrinkage in First Pass given Total Shrinkage?

Transverse Shrinkage in First Pass given Total Shrinkage calculator uses Transverse Shrinkage in First Pass = Total Transverse Shrinkage-Constant for Multi-Pass Shrinkage*(log10(Total Weight of Weld Metal Deposited/Weld Metal Deposited in First Pass)) to calculate the Transverse Shrinkage in First Pass, The Transverse Shrinkage in First Pass given Total Shrinkage formula is defined as the shrinkage occurring perpendicular to the weld line. Transverse Shrinkage in First Pass is denoted by S0 symbol.

How to calculate Transverse Shrinkage in First Pass given Total Shrinkage using this online calculator? To use this online calculator for Transverse Shrinkage in First Pass given Total Shrinkage, enter Total Transverse Shrinkage (St), Constant for Multi-Pass Shrinkage (b), Total Weight of Weld Metal Deposited (w) & Weld Metal Deposited in First Pass (w0) and hit the calculate button. Here is how the Transverse Shrinkage in First Pass given Total Shrinkage calculation can be explained with given input values -> 2010.396 = 0.0053-0.24*(log10(0.00515/0.00499)).

FAQ

What is Transverse Shrinkage in First Pass given Total Shrinkage?
The Transverse Shrinkage in First Pass given Total Shrinkage formula is defined as the shrinkage occurring perpendicular to the weld line and is represented as S0 = St-b*(log10(w/w0)) or Transverse Shrinkage in First Pass = Total Transverse Shrinkage-Constant for Multi-Pass Shrinkage*(log10(Total Weight of Weld Metal Deposited/Weld Metal Deposited in First Pass)). Total Transverse shrinkage is the amount by which weldment shrinks due to multiple passes, Constant for Multi-Pass Shrinkage is used for calculating total transverse shrinkage due to multi-pass welding, Total Weight of Weld Metal Deposited is the amount of metal deposited during welding & Weld Metal Deposited in First Pass is just metal deposited in single pass of welding.
How to calculate Transverse Shrinkage in First Pass given Total Shrinkage?
The Transverse Shrinkage in First Pass given Total Shrinkage formula is defined as the shrinkage occurring perpendicular to the weld line is calculated using Transverse Shrinkage in First Pass = Total Transverse Shrinkage-Constant for Multi-Pass Shrinkage*(log10(Total Weight of Weld Metal Deposited/Weld Metal Deposited in First Pass)). To calculate Transverse Shrinkage in First Pass given Total Shrinkage, you need Total Transverse Shrinkage (St), Constant for Multi-Pass Shrinkage (b), Total Weight of Weld Metal Deposited (w) & Weld Metal Deposited in First Pass (w0). With our tool, you need to enter the respective value for Total Transverse Shrinkage, Constant for Multi-Pass Shrinkage, Total Weight of Weld Metal Deposited & Weld Metal Deposited in First Pass and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!