Vessel Wall Thickness for Channel Type Jacket Solution

STEP 0: Pre-Calculation Summary
Formula Used
Vessel Thickness = Design Length of Channel Section*sqrt((0.167*Design Jacket Pressure)/(Allowable Stress for Jacket Material))+Corrosion Allowance
tvessel = d*sqrt((0.167*pj)/(fj))+c
This formula uses 1 Functions, 5 Variables
Functions Used
sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)
Variables Used
Vessel Thickness - (Measured in Millimeter) - Vessel thickness refers to the thickness of the walls of a pressure vessel, which is a container designed to hold gases or liquids at a pressure significantly different from the ambient pressure.
Design Length of Channel Section - (Measured in Millimeter) - Design Length of Channel Section is the distance between the centre of reactions between channel section.
Design Jacket Pressure - (Measured in Newton per Square Millimeter) - Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions.
Allowable Stress for Jacket Material - (Measured in Newton per Square Millimeter) - Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one.
Corrosion Allowance - (Measured in Millimeter) - Corrosion allowance is defined as an extra thickness normally added to carbon and low alloy steel to mitigate the CO2 corrosion rate.
STEP 1: Convert Input(s) to Base Unit
Design Length of Channel Section: 72.3 Millimeter --> 72.3 Millimeter No Conversion Required
Design Jacket Pressure: 0.105 Newton per Square Millimeter --> 0.105 Newton per Square Millimeter No Conversion Required
Allowable Stress for Jacket Material: 120 Newton per Square Millimeter --> 120 Newton per Square Millimeter No Conversion Required
Corrosion Allowance: 10.5 Millimeter --> 10.5 Millimeter No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
tvessel = d*sqrt((0.167*pj)/(fj))+c --> 72.3*sqrt((0.167*0.105)/(120))+10.5
Evaluating ... ...
tvessel = 11.3739781182902
STEP 3: Convert Result to Output's Unit
0.0113739781182902 Meter -->11.3739781182902 Millimeter (Check conversion here)
FINAL ANSWER
11.3739781182902 11.37398 Millimeter <-- Vessel Thickness
(Calculation completed in 00.004 seconds)

Credits

Created by Heet
Thadomal Shahani Engineering College (Tsec), Mumbai
Heet has created this Calculator and 200+ more calculators!
Verified by Prerana Bakli
University of Hawaiʻi at Mānoa (UH Manoa), Hawaii, USA
Prerana Bakli has verified this Calculator and 1600+ more calculators!

21 Jacketed Reaction Vessel Calculators

Total Axial Stress in Vessel Shell
Go Total Axial Stress = ((Internal Pressure in Vessel*Internal Diameter of Shell)/(4*Shell Thickness*Joint Efficiency for Shell))+((Design Jacket Pressure*Internal Diameter of Half Coil)/(2*Shell Thickness*Joint Efficiency for Shell))+(2*Maximum difference between Coil and Shell Pressure*(Outer Diameter of Half Coil)^(2))/(3*Shell Thickness^(2))
Maximum Equivalent Stress at Junction with Shell
Go Maximum Equivalent Stress at Junction with Shell = (sqrt((Total Axial Stress)^(2)+(Total Hoop Stress)^(2)+(Maximum Hoop Stress in Coil at Junction with Shell)^(2)-((Total Axial Stress*Total Hoop Stress)+(Total Axial Stress*Maximum Hoop Stress in Coil at Junction with Shell)+(Maximum Hoop Stress in Coil at Junction with Shell*Total Hoop Stress))))
Total Hoop Stress in Shell
Go Total Hoop Stress = (Design Pressure Shell*Internal Diameter of Shell)/(2*Shell Thickness*Joint Efficiency for Shell)+(Design Jacket Pressure*Internal Diameter of Half Coil)/((4*Thickness of Half Coil Jacket*Weld Joint Efficiency Factor for Coil)+(2.5*Shell Thickness*Joint Efficiency for Shell))
Combined Moment of Inertia of Shell and Stiffener per Unit Length
Go Combined Moment of Inertia of Shell and Stiffener = (Vessel Shell Outer Diameter^(2)*Effective Length Between Stiffeners*(Shell Thickness for Jackted Reaction Vessel+Cross Sectional Area of Stiffening Ring/Effective Length Between Stiffeners)*Allowable Stress for Jacket Material)/(12*Modulus of Elasticity Jacketed Reaction Vessel)
Shell Thickness for Critical External Pressure
Go Critical External Pressure = (2.42*Modulus of Elasticity Jacketed Reaction Vessel)/(1-(Poisson Ratio)^(2))^(3/4)*((Vessel Thickness/Vessel Shell Outer Diameter)^(5/2)/((Length of Shell/Vessel Shell Outer Diameter)-0.45*(Vessel Thickness/Vessel Shell Outer Diameter)^(1/2)))
Depth of Torisperical Head
Go Depth of Head = Crown Radius for Jacketed Reaction Vessel-sqrt((Crown Radius for Jacketed Reaction Vessel-Vessel Shell Outer Diameter/2)*(Crown Radius for Jacketed Reaction Vessel+Vessel Shell Outer Diameter/2-2*Knuckle Radius))
Design of Shell Thickness Subjected to Internal Pressure
Go Shell Thickness for Jackted Reaction Vessel = (Internal Pressure in Vessel*Internal Diameter of Shell)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell)-(Internal Pressure in Vessel))+Corrosion Allowance
Maximum Axial Stress in Coil at Junction with Shell
Go Maximum Axial Stress in Coil at Junction = (Design Jacket Pressure*Internal Diameter of Half Coil)/((4*Thickness of Half Coil Jacket*Weld Joint Efficiency Factor for Coil)+(2.5*Shell Thickness*Joint Efficiency for Shell))
Dished Head Thickness
Go Dished Head Thickness = ((Internal Pressure in Vessel*Crown Radius for Jacketed Reaction Vessel*Stress Intensification Factor)/(2*Allowable Stress for Jacket Material*Joint Efficiency for Shell))+Corrosion Allowance
Thickness of Bottom Head subjected to Pressure
Go Head Thickness = 4.4*Crown Radius for Jacketed Reaction Vessel*(3*(1-(Poisson Ratio)^(2)))^(1/4)*sqrt(Internal Pressure in Vessel/(2*Modulus of Elasticity Jacketed Reaction Vessel))
Thickness of Half Coil Jacket
Go Thickness of Half Coil Jacket = (Design Jacket Pressure*Internal Diameter of Half Coil)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell))+Corrosion Allowance
Thickness of Jacket Shell for Internal Pressure
Go Required Thickness of Jacket = (Design Jacket Pressure*Internal Diameter of Shell)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell)-Design Jacket Pressure)
Channel Jacket Thickness
Go Channel Wall Thickness = Design Length of Channel Section*(sqrt((0.12*Design Jacket Pressure)/(Allowable Stress for Jacket Material)))+Corrosion Allowance
Maximum Hoop Stress in Coil at Junction with Shell
Go Maximum Hoop Stress in Coil at Junction with Shell = (Design Jacket Pressure*Internal Diameter of Half Coil)/(2*Thickness of Half Coil Jacket*Weld Joint Efficiency Factor for Coil)
Vessel Wall Thickness for Channel Type Jacket
Go Vessel Thickness = Design Length of Channel Section*sqrt((0.167*Design Jacket Pressure)/(Allowable Stress for Jacket Material))+Corrosion Allowance
Required Plate Thickness for Dimple Jacket
Go Required Thickness of Dimple Jacket = Maximum Pitch between Steam Weld Centre Lines*sqrt(Design Jacket Pressure/(3*Allowable Stress for Jacket Material))
Required Thickness for Jacket Closer Member with Jacket Width
Go Required Thickness for Jacket Closer Member = 0.886*Jacket Width*sqrt(Design Jacket Pressure/Allowable Stress for Jacket Material)
Length of Shell under Combined Moment of Inertia
Go Length of Shell = 1.1*sqrt(Vessel Shell Outer Diameter*Vessel Thickness)
Cross Sectional Area of Stiffening Ring
Go Cross Sectional Area of Stiffening Ring = Width of Stiffener*Thickness of Stiffener
Length of Shell for Jacket
Go Length of Shell for Jacket = Length of Straight Side Jacket+1/3*Depth of Head
Jacket Width
Go Jacket Width = (Inside Diameter of Jacket-Outer Diameter of Vessel)/2

Vessel Wall Thickness for Channel Type Jacket Formula

Vessel Thickness = Design Length of Channel Section*sqrt((0.167*Design Jacket Pressure)/(Allowable Stress for Jacket Material))+Corrosion Allowance
tvessel = d*sqrt((0.167*pj)/(fj))+c

What is Design Thickness?

Design thickness is a term used in structural engineering to refer to the thickness of a structural element (such as a beam, column, or plate) that has been calculated or specified based on the design requirements of the structure. The design thickness is the thickness that has been calculated or specified based on the structural requirements of the beam and the strength and deformability of the soil or foundation on which the beam will be supported. The design thickness of a bottom plate is typically determined by a structural engineer or using structural engineering software, and is used to ensure that the bottom plate is able to safely carry the loads that will be applied to it during the life of the structure.

How to Calculate Vessel Wall Thickness for Channel Type Jacket?

Vessel Wall Thickness for Channel Type Jacket calculator uses Vessel Thickness = Design Length of Channel Section*sqrt((0.167*Design Jacket Pressure)/(Allowable Stress for Jacket Material))+Corrosion Allowance to calculate the Vessel Thickness, Vessel Wall Thickness for Channel Type Jacket refers to the minimum required thickness of the wall of a vessel that is designed with an external jacket for heating or cooling purposes. Vessel Thickness is denoted by tvessel symbol.

How to calculate Vessel Wall Thickness for Channel Type Jacket using this online calculator? To use this online calculator for Vessel Wall Thickness for Channel Type Jacket, enter Design Length of Channel Section (d), Design Jacket Pressure (pj), Allowable Stress for Jacket Material (fj) & Corrosion Allowance (c) and hit the calculate button. Here is how the Vessel Wall Thickness for Channel Type Jacket calculation can be explained with given input values -> 11373.98 = 0.0723*sqrt((0.167*105000)/(120000000))+0.0105.

FAQ

What is Vessel Wall Thickness for Channel Type Jacket?
Vessel Wall Thickness for Channel Type Jacket refers to the minimum required thickness of the wall of a vessel that is designed with an external jacket for heating or cooling purposes and is represented as tvessel = d*sqrt((0.167*pj)/(fj))+c or Vessel Thickness = Design Length of Channel Section*sqrt((0.167*Design Jacket Pressure)/(Allowable Stress for Jacket Material))+Corrosion Allowance. Design Length of Channel Section is the distance between the centre of reactions between channel section, Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions, Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one & Corrosion allowance is defined as an extra thickness normally added to carbon and low alloy steel to mitigate the CO2 corrosion rate.
How to calculate Vessel Wall Thickness for Channel Type Jacket?
Vessel Wall Thickness for Channel Type Jacket refers to the minimum required thickness of the wall of a vessel that is designed with an external jacket for heating or cooling purposes is calculated using Vessel Thickness = Design Length of Channel Section*sqrt((0.167*Design Jacket Pressure)/(Allowable Stress for Jacket Material))+Corrosion Allowance. To calculate Vessel Wall Thickness for Channel Type Jacket, you need Design Length of Channel Section (d), Design Jacket Pressure (pj), Allowable Stress for Jacket Material (fj) & Corrosion Allowance (c). With our tool, you need to enter the respective value for Design Length of Channel Section, Design Jacket Pressure, Allowable Stress for Jacket Material & Corrosion Allowance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!